Self Reported Power States
SSDs in general save energy by switching between different power modes depending on how busy they are. When working hard, they use more power, when idle, they go into low-power or sleep states to save energy. These modes help the SSD balance performance and power consumption, but since the reported power figures are not always accurate, we conduct our own tests to verify real-world behavior.
Manufacturers define the values in the NVMe Power States table and, based on internal estimates or lab testing, store them in firmware—not standardized measurements. These values, like max power and latency, aren't verified by any third-party body and may not reflect actual behavior. They're often derived from worst-case scenarios, simulations, or controller configuration limits.
| NVMe Power States Configuration |
|---|
| SSD | Silicon Motion MonTitan 7.68 TB |
|---|
| Controller | Silicon Motion MonTitan SM8366 |
|---|
| NAND Flash | Micron 3D eTLC B58R 1 Tb C-Die 232-Layers |
|---|
| Firmware | TNBSA060 |
|---|
| Caution Temperature | 77°C |
|---|
| Critical Temperature | 85°C |
|---|
| Power States |
|---|
| Power State | Max Power | Active | Entry Latency | Exit Latency |
|---|
| PS 0 | 25.00 W | Active (25.00 W) | 22000 µs | 37000 µs |
| PS 1 | 24.00 W | Active (24.00 W) | 22000 µs | 37000 µs |
| PS 2 | 23.00 W | Active (23.00 W) | 22000 µs | 37000 µs |
| PS 3 | 22.00 W | Active (22.00 W) | 22000 µs | 37000 µs |
| PS 4 | 21.00 W | Active (21.00 W) | 22000 µs | 37000 µs |
| PS 5 | 20.00 W | Active (20.00 W) | 22000 µs | 37000 µs |
| PS 6 | 19.00 W | Active (19.00 W) | 22000 µs | 37000 µs |
| PS 7 | 18.00 W | Active (18.00 W) | 22000 µs | 37000 µs |
| PS 8 | 17.00 W | Active (17.00 W) | 22000 µs | 37000 µs |
| PS 9 | 16.00 W | Active (16.00 W) | 22000 µs | 37000 µs |
| PS 10 | 15.00 W | Active (15.00 W) | 22000 µs | 37000 µs |
| PS 11 | 14.00 W | Active (14.00 W) | 22000 µs | 37000 µs |
| PS 12 | 13.00 W | Active (13.00 W) | 22000 µs | 37000 µs |
| PS 13 | 12.00 W | Active (12.00 W) | 22000 µs | 37000 µs |
The drive features fourteen primary power states, all of which are active and draw a certain level of power. However, even though some of these states go up to "25 W," that doesn't mean the drive will sustain that level of power consumption under all workloads—just like a graphics card such as the RTX 5090, with its 600 W TDP, doesn't constantly operate at maximum power draw.
According to the information reported by the drive, the latencies between the active power states of the MonTitan are relative low. This indicates that the SSD is configured to transition between these active states without introducing any additional switching delay. However, it's important to note that when the drive enters lower sub-power states during idle periods, it may exhibit higher latencies. As the table title suggests, these values reflect what is reported by the SMART system and may not necessarily represent real-world behavior under all conditions.
However, throughout all our test sessions, as we will see later in this review, its power consumption remained below PS 0, which is reported as 25 W according to SMART.