XPG Lancer Blade RGB DDR5-5600 16 GB CL46 Review - Low Profile 23

XPG Lancer Blade RGB DDR5-5600 16 GB CL46 Review - Low Profile

Memory Average FPS »

Relative Performance

1920×1080 Relative Performance


On the Intel Core Ultra 285K, the XPG Lancer Blade RGB 5600 sits at the 100% baseline in both Average FPS and 1% Lows, which places it at the very bottom of the entire chart below even JEDEC DDR5-5600 16 GB DIMMs at 101–102%, and well behind the competitive DDR5 XMP configurations that reach 105–113% above it. The 200S Boost profile gives it a marginal 1–2% nudge, but it remains anchored at the bottom. The chart makes clear that the bandwidth limitation imposed by the missing four ICs is a real and measurable handicap, and no amount of frequency or profile tuning fully compensates for the fundamental throughput ceiling that half-populated 8 GB DIMMs impose.


On the Intel Core i9-13900K, the XPG Lancer Blade RGB 5600 is shown at the 100% baseline. It ties with DDR5-4800 JEDEC, a kit running at significantly lower frequency with full 16 GB DIMMs and their complete IC complement. The bandwidth deficit from the missing four ICs per module is effectively dragging the 5600 MT/s kit down to the performance level of slow JEDEC DDR5, despite running at a higher clock. Every properly populated DDR5 kit above it from DDR5-6400 to DDR5-8200 pulls meaningfully ahead, and even JEDEC DDR5-5600 with full 16 GB DIMMs manages 102% in both metrics. A small but consistent advantage that again points directly to IC count and bandwidth capacity as the differentiating factor. The XPG kit does stay ahead of all DDR4 configurations (91–95%), so it isn't without merit, but the overall picture on Raptor Lake reinforces the same conclusion as Arrow Lake: 8 GB DIMMs with their halved IC population represent a meaningful structural bandwidth limitation that holds back real-world gaming performance regardless of the frequency printed on the label.


This is the 9-game average on the AMD Ryzen 9950X, and it summarizes the trend seen throughout: the XPG Lancer Blade RGB 5600 sits at the 100% baseline, trailing every kit tested including same-frequency JEDEC DDR5-5600 (103/105%) and lower-frequency JEDEC DDR5-4800 (102/103%). The gap widens to 8-12% against the top DDR5-6000/6400 kits. Averaged across all nine games, this confirms the XPG kit's reduced IC count is a consistent, platform-wide bandwidth penalty on AMD.


3840×2160 Relative Performance

At 4K, the picture changes completely for the XPG Lancer Blade RGB 5600 across all three platforms, and it's the clearest demonstration yet of GPU-bound gaming. On the AMD Ryzen 9950X, the XPG kit is within 2% of every other configuration. On the Intel Core i9-13900K, it again sits comfortably mid-pack at 100%, within 1–3% of virtually every DDR5 kit regardless of frequency or capacity. On the Intel Core Ultra 285K, the entire chart compresses into an incredibly tight 100–102% band, with the XPG kit essentially indistinguishable from DDR5-8400, DDR5-8800, and even some boosted profiles. Despite its bandwidth-limited 8 GB DIMMs missing four ICs per module, none of that matters here. Once the RTX 4090 becomes the bottleneck at 4K, the GPU simply can't render frames fast enough for memory bandwidth or latency differences to show up in the final frame rate. This is the clearest possible proof that memory kit selection matters far more at 1080p and other CPU-bound resolutions than it does at 4K, where nearly any reasonable DDR5 kit will suffice.



Next Page »Memory Average FPS
View as single page
Nov 18th, 2026 21:28 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts