Friday, August 1st 2025

Thermal Grizzly Releases New DeltaMate Fittings

Press Release by
GFreeman
 Discuss (8 Comments)
Thermal Grizzly is proud to announce the first category in our new DeltaMate product line: water-cooling fittings. The DeltaMate fittings can be combined to accommodate virtually any tubing configuration. They support soft tubes (ST) with 16 mm OD / 10 mm ID and hard tubes (HT) with a 16 mm outer diameter. All fittings are machined from brass and finished with a matte-black chromium plating.

We're launching with nine modular products divided into four categories:
  • DeltaMate Fitting
  • DeltaMate Rotary
  • DeltaMate Extender
  • Accessory fittings for water cooling
DeltaMate Fitting - ST16
  • Single tapered barb allows straightforward installation for a wide range of flexible tubes.
  • Knurled compression ring securely grips the tubing with high retention force.
  • Compact overall dimensions facilitate installation in almost any watercooling loop.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Robust design allows installation with an 8 mm hex key.
DeltaMate Fitting - HT 16
  • Flat base enables tubing to be installed from any direction with complete visibility.
  • High surface area custom O-ring securely grips the tubing with high retention force.
  • Compact overall dimensions facilitate installation in almost any watercooling loop.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Robust design allows installation with an 8 mm hex key.
DeltaMate Rotary - 90°
  • Small dimensions allow modular combination with other DeltaMate Rotary and Extender Fittings.
  • Subsequent fittings mechanically lock the rotary joint together for maximum security.
  • Includes an optional aesthetic cover with DeltaMate logo that can be rotated to any orientation.
  • Elegant and minimal design integrates seamlessly with all DeltaMate fittings.
  • Easy to install in tight places and SFF builds using an 8 mm hex key.
DeltaMate Rotary - T
  • Small dimensions allow modular combination with other DeltaMate Rotary and Extender Fittings.
  • Subsequent fittings mechanically lock the rotary joint together for maximum security.
  • Includes an optional aesthetic cover with DeltaMate logo that can be rotated to any orientation.
  • Elegant and minimal design integrates seamlessly with all DeltaMate fittings.
  • Easy to install in tight places and SFF builds using an 8 mm hex key.
Delta Mate Extender - MF7
  • Can be combined with two DeltaMate Rotary - 90° to create a Double Rotary with an offset of 28 mm.
  • Practical fixed length extender to increase the spacing between ports and fittings by 7 mm.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Robust design allows installation with an 8 mm hex key.
DeltaMate Extender - MF 10
  • Can be combined with a DeltaMate Rotary to create a direct replacement for conventional rotary fittings.
  • Practical fixed length extender to increase the spacing between ports and fittings by 10.5 mm.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Robust design allows installation with an 8 mm hex key.
DeltaMate Extender - MF 14
  • Practical fixed length extender to increase the spacing between ports and fittings by 14 mm.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Robust design allows installation with an 8 mm hex key.
DeltaMate Extender - MF28
  • Commonly used to add clearance for memory modules and fans or two parallel tubes in the same plane.
  • Practical fixed length extender to increase the spacing between ports and fittings by 28 mm.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Robust design allows installation with an 8 mm hex key.
DeltaMate Plug
  • Simple low profile plug that can be used to block any G1/4" female ports.
  • Includes an optional aesthetic cover with DeltaMate logo that can be rotated to any orientation.
  • Consistent outer diameter with all DeltaMate fittings for completely seamless integration.
  • Easy to install in tight places and SFF builds using an 8 mm hex key.
Source: Thermal Grizzly

Related News

Add your own comment

8 Comments on Thermal Grizzly Releases New DeltaMate Fittings

#1
teamtd11
Good to see the soft tube 10/16. Might be something for a future refurb of my cooling. Replace these EK fittings...
Posted on Reply
#2
huggi
I noticed the article doesn't show prices although they are up on Thermal Grizzly's webstore. Here are the prices shown on their store for a single item (prices include VAT):
  • [ICODE]ST16 €7.90 / $9.24[/ICODE]
  • [ICODE]HT16 €8.90 / $10.41[/ICODE]
  • [ICODE]Rotary 90 €10.90 / $12.75[/ICODE]
  • [ICODE]Rotary T €11.90 / $13.92[/ICODE]
  • [ICODE]Extender MF7 €4.90 / $5.73[/ICODE]
  • [ICODE]Extender MF10 €5.40 / $6.32[/ICODE]
  • [ICODE]Extender MF14 €5.90 / $6.90[/ICODE]
  • [ICODE]Extender MF28 €6.90 / $8.07[/ICODE]
  • [ICODE]Plug €5.90 / $6.90[/ICODE]
Seems quite expensive although I guess that's on par for TG.
Posted on Reply
#3
RejZoR
huggiI noticed the article doesn't show prices although they are up on Thermal Grizzly's webstore. Here are the prices shown on their store for a single item (prices include VAT):
  • [ICODE]ST16 €7.90 / $9.24[/ICODE]
  • [ICODE]HT16 €8.90 / $10.41[/ICODE]
  • [ICODE]Rotary 90 €10.90 / $12.75[/ICODE]
  • [ICODE]Rotary T €11.90 / $13.92[/ICODE]
  • [ICODE]Extender MF7 €4.90 / $5.73[/ICODE]
  • [ICODE]Extender MF10 €5.40 / $6.32[/ICODE]
  • [ICODE]Extender MF14 €5.90 / $6.90[/ICODE]
  • [ICODE]Extender MF28 €6.90 / $8.07[/ICODE]
  • [ICODE]Plug €5.90 / $6.90[/ICODE]
Seems quite expensive although I guess that's on par for TG.
They probably actually machine them in Germany, in-house which is why the prices are high. In a way I can't blame Roman. Cost of living in Germany is high, but keeping it in-house means the products are really premium with tight QC. When I want premium thermal paste, I don't mind paying premium for Thermal Grizzly ones. I can see how people building a premium watercooling system think the same. If you want something cheap, there is already tons of cheap Chinese products of which some actually aren't that bad, but you get the idea.
Posted on Reply
#4
dgianstefani
TPU Proofreader
RejZoRThey probably actually machine them in Germany, in-house which is why the prices are high. In a way I can't blame Roman. Cost of living in Germany is high, but keeping it in-house means the products are really premium with tight QC. When I want premium thermal paste, I don't mind paying premium for Thermal Grizzly ones. I can see how people building a premium watercooling system think the same. If you want something cheap, there is already tons of cheap Chinese products of which some actually aren't that bad, but you get the idea.
Also, these aren't that expensive for quality. EK, Corsair, Optimus etc, all similar pricing.
Posted on Reply
#5
wNotyarD
huggiI noticed the article doesn't show prices although they are up on Thermal Grizzly's webstore. Here are the prices shown on their store for a single item (prices include VAT):
  • [ICODE]ST16 €7.90 / $9.24[/ICODE]
  • [ICODE]HT16 €8.90 / $10.41[/ICODE]
  • [ICODE]Rotary 90 €10.90 / $12.75[/ICODE]
  • [ICODE]Rotary T €11.90 / $13.92[/ICODE]
  • [ICODE]Extender MF7 €4.90 / $5.73[/ICODE]
  • [ICODE]Extender MF10 €5.40 / $6.32[/ICODE]
  • [ICODE]Extender MF14 €5.90 / $6.90[/ICODE]
  • [ICODE]Extender MF28 €6.90 / $8.07[/ICODE]
  • [ICODE]Plug €5.90 / $6.90[/ICODE]
Seems quite expensive although I guess that's on par for TG.
Isn't the TG water cooling crew composed of many people who came from EK as well? Further reason for the price tags.
Posted on Reply
#6
Broken Processor
teamtd11Good to see the soft tube 10/16. Might be something for a future refurb of my cooling. Replace these EK fittings...
I hope they do 13/10 it's the only size tubing I'll use now so easy to work with and hide when needed. And micro fittings!
Posted on Reply
#7
Panther_Seraphin
wNotyarDIsn't the TG water cooling crew composed of many people who came from EK as well? Further reason for the price tags.
I do believe TG got a few people from EK including I believe their previous head designer

TG are keeping a lot of production in house when possible and only outsourcing from previous videos when its either impossible to compete in quality or they dont have the ability to do it in house from my understanding.
Posted on Reply
#8
mkppo
Where's that astral 5090 block and their new CPU block dammit. Seems like it's been ages since they announced it
Posted on Reply
Aug 1st, 2025 22:40 CDT change timezone

Latest GPU Drivers

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts