How to enable additional shaders on Radeon HD 6950

[onehans]

lucky you!!

any more than 1100 vc and 880 core brings artifacts so i have to stay with my new 6970 still good score

i think is time to get drukt i sit in hire last 6 h

 

[manofthem]

any more than 1100 vc and 880 core brings artifacts so i have to stay with my new 6970 still good score

i think is time to get drukt i sit in hire last 6 h

You should be able to get more voltage than that, that's default voltage.

 

[onehans]

You should be able to get more voltage than that, that's default voltage.

As soon I go over defaults I get artifacts straight away in windows7 :/ duno. and idle is 32 I have stock cooler. Flashed with 6970 as bios from forum gave me artifacts too

 

[manofthem]

As soon I go over defaults I get artifacts straight away in windows7 :/ duno. and idle is 32 I have stock cooler. Flashed with 6970 as bios from forum gave me artifacts too

You've probably said it already, but are you using a modded 6950 bios or a 6970 bios?

 

[onehans]

You've probably said it already, but are you using a modded 6950 bios or a 6970 bios?

It a 6970 bios, moded one did not like my card and giving me artefacts :/

 

[manofthem]

It a 6970 bios, moded one did not like my card and giving me artefacts :/

any more than 1100 vc and 880 core brings artifacts so i have to stay with my new 6970 still good score

If it's a 6970 bios, voltage should be at 1.1.75, not 1.1 Can you check gpuz to see which it's running at?

 

[onehans]

If it's a 6970 bios, voltage should be at 1.1.75, not 1.1 Can you check gpuz to see which it's running at?

I went for beer but ill check it 2morrow. ill be back in here in about 15h

 

[manofthem]

I went for beer but ill check it 2morrow. ill be back in here in about 15h

Beer sounds nice and right

 

[Ron Jeremy]

Ok, so I have a Diamond 6950 that absolutely refuses to unlock it's shaders, even when Winflash, RBE and DOS complete "successful" flashes. When I run the batch file (W1zzard), I get "Could not find byte sequence in file". I have tried EVERY method I have seen and GPU-Z still shows 1408....I have reinstalled drivers, turned UAC off..etc etc. I also have a Sapphire 6950 that flashed the shaders flawlessly when W1zzard first wrote the batch. Any ideas? And yes, the switch is in #1 position.

 

[Kingken]

Apologies if this has been answered before i have been trawling this thread!

Card: Sapphire ATI Radeon HD 6950 "Dual Fan Edition" 2048MB GDDR5 PCI-Express Graphics Card [11188-05-50G]

I followed the guide from here:

http://www.techpowerup.com/articles/overclocking/159

Managed to unlock the bios then upgrade to 6970 bios fine could see the extra shaders. But after rebooting back into win7 desktop kept freezing/going black, and lots of ATI errors in system tray reporting recovering from errors driver restarting or something.

So i ended up flicking the switch back to the standard bios feeling most deflated, until i saw this thread offering hope.

Can anyone assist me in what i might of done wrong or i read here about add unlocking shaders in 6950 bios and or adjusting voltages, what's the best way for my card? Many thanks in advance.

 

[Ginnoskie]

Apologies if this has been answered before i have been trawling this thread!

Card: Sapphire ATI Radeon HD 6950 "Dual Fan Edition" 2048MB GDDR5 PCI-Express Graphics Card [11188-05-50G]

I followed the guide from here:

http://www.techpowerup.com/articles/overclocking/159

Managed to unlock the bios then upgrade to 6970 bios fine could see the extra shaders. But after rebooting back into win7 desktop kept freezing/going black, and lots of ATI errors in system tray reporting recovering from errors driver restarting or something.

So i ended up flicking the switch back to the standard bios feeling most deflated, until i saw this thread offering hope.

Can anyone assist me in what i might of done wrong or i read here about add unlocking shaders in 6950 bios and or adjusting voltages, what's the best way for my card? Many thanks in advance.

As we all know that the safest thing to do is the unlock shaders only..have you tried the unlock shaders only?

 

[Ginnoskie]

Apologies if this has been answered before i have been trawling this thread!

Card: Sapphire ATI Radeon HD 6950 "Dual Fan Edition" 2048MB GDDR5 PCI-Express Graphics Card [11188-05-50G]

I followed the guide from here:

http://www.techpowerup.com/articles/overclocking/159

Managed to unlock the bios then upgrade to 6970 bios fine could see the extra shaders. But after rebooting back into win7 desktop kept freezing/going black, and lots of ATI errors in system tray reporting recovering from errors driver restarting or something.

So i ended up flicking the switch back to the standard bios feeling most deflated, until i saw this thread offering hope.

Can anyone assist me in what i might of done wrong or i read here about add unlocking shaders in 6950 bios and or adjusting voltages, what's the best way for my card? Many thanks in advance.

Have you tried uninstalling and re installing drivers?? sometimes that might just help..

 

[Kingken]

As we all know that the safest thing to do is the unlock shaders only..have you tried the unlock shaders only?

No not tried that how do i unlock shaders only..?

 

[Ginnoskie]

No not tried that how do i unlock shaders only..?

Try to follow this guide.. http://forums.extremeoverclocking.com/t355592.html

Then give me an update so i can help which problem you have..

 

[onehans]

If it's a 6970 bios, voltage should be at 1.1.75, not 1.1 Can you check gpuz to see which it's running at?

gpu-z shows 1,1500v and afterburner - got adjustable vc slider but does not change any vc ?? again i try other version of afterburner. plus today i dont get artifacts going with 920 in windows and combustor so i check it in 3dmark11 now

so card runs stable at core 915mhz and 1410 mem but vcore slider dont work :/ i will look for some other solution rather afterburner

 

[Noci]

unlock succesfull

Thanx W1zzard, works like a charm.

Very clear explanation, finished it within a few minutes.

I've a VTX3D 6950 1Gb (art: VX6950 1GBD5-2DH look @ http://www.vtx3d.com/products_features.asp?id=96) and the RBE method worked. The card was purchased only a month ago (€ 189,90 @ pixmania), so it looks like AMD does not 'hard' lock al Cayman chips.
It's quite a happy moment, after the disappointment that my AMD Phenom II x4 690T CPU had no unlockable cores.

This is my first time on this forum so I'll have to figure out how to upload a picture to show the proof.

First I'll read my way through this topic than do some stabillity tests, benchmarking and carefull OC. I'm also thinking of getting another identical card to create my first CF configuration.

2 x 6970 in CF for less than € 400,-, sounds good to me.

Thanks again, people like you make computing fun again

 

[Ginnoskie]

Thanx W1zzard, works like a charm.

Very clear explanation, finished it within a few minutes.

I've a VTX3D 6950 1Gb (art: VX6950 1GBD5-2DH look @ http://www.vtx3d.com/products_features.asp?id=96) and the RBE method worked. The card was purchased only a month ago (€ 189,90 @ pixmania), so it looks like AMD does not 'hard' lock al Cayman chips.
It's quite a happy moment, after the disappointment that my AMD Phenom II x4 690T CPU had no unlockable cores.

This is my first time on this forum so I'll have to figure out how to upload a picture to show the proof.

First I'll read my way through this topic than do some stabillity tests, benchmarking and carefull OC. I'm also thinking of getting another identical card to create my first CF configuration.

2 x 6970 in CF for less than € 400,-, sounds good to me.

Thanks again, people like you make computing fun again

Cheers for that mate!!

 

[Rule-R]

This is my first time on this forum so I'll have to figure out how to upload a picture to show the proof.

TPU Image upload

when youve uploaded an image, just copy the bbcode in a post

 

[Ginnoskie]

gpu-z shows 1,1500v and afterburner - got adjustable vc slider but does not change any vc ?? again i try other version of afterburner. plus today i dont get artifacts going with 920 in windows and combustor so i check it in 3dmark11 now

so card runs stable at core 915mhz and 1410 mem but vcore slider dont work :/ i will look for some other solution rather afterburner

Did you flash it to 6970 bios or it's just the unlocked shaders? because if you flashed it to 6970 bios there's no need for voltage control it's already set to 1.175v.

 

[onehans]

Did you flash it to 6970 bios or it's just the unlocked shaders? because if you flashed it to 6970 bios there's no need for voltage control it's already set to 1.175v.

i flashed to 6970 but i was playing LA noire and system crash after around 15 min so i played batman arkham city and it crashes after 1h :/
so i turned my a8-3870k processor to stock 3Ghz from 3,5 and i got same result :?

maybe if i unlock shaders on my 6950 stock bios and overclock will help? as bios from forum gives me artifacts

 

[Ginnoskie]

i flashed to 6970 but i was playing LA noire and system crash after around 15 min so i played batman arkham city and it crashes after 1h :/
so i turned my a8-3870k processor to stock 3Ghz from 3,5 and i got same result :?

maybe if i unlock shaders on my 6950 stock bios and overclock will help? as bios from forum gives me artifacts

hmmm..what driver are you using? i have mine flashed to 6970 with 11.12 drivers, no issues or whatsoever. try the unlock shaders only then give me a feedback if the problem still exist..
and can i ask what PSU are you using and how many watts? maybe you're you're Powersupply is out of juice and that's causing the problem..because as i can see you overclocked it way too high..

 

[onehans]

hmmm..what driver are you using? i have mine flashed to 6970 with 11.12 drivers, no issues or whatsoever. try the unlock shaders only then give me a feedback if the problem still exist..
and can i ask what PSU are you using and how many watts? maybe you're you're Powersupply is out of juice and that's causing the problem..because as i can see you overclocked it way too high..

i changed drivers to http://support.amd.com/us/kbarticles/Pages/AMDCatalyst1012ahotfix.aspx 2010.1215 just to see if this let me control vcore (update still does not work :/ )
my psu got 750w (OCZ) processor A8-3870 on ASRock pro4 and mem- PC192000 one hard drive sata and dvdrw sata too, so hould be enough
and even going back to 880/1375 cause same effect, crash in LAnoire after 15min and in batman in 1h time gameplay

i will flash it back to unlock shaders only but when i comeback from holiday im going tomorrow morning and be back in 9 days

thank you very much for ur kind help

 

[Ginnoskie]

i changed drivers to http://support.amd.com/us/kbarticles/Pages/AMDCatalyst1012ahotfix.aspx 2010.1215 just to see if this let me control vcore (update still does not work :/ )
my psu got 750w (OCZ) processor A8-3870 on ASRock pro4 and mem- PC192000 one hard drive sata and dvdrw sata too, so hould be enough
and even going back to 880/1375 cause same effect, crash in LAnoire after 15min and in batman in 1h time gameplay

i will flash it back to unlock shaders only but when i comeback from holiday im going tomorrow morning and be back in 9 days

thank you very much for ur kind help

ok..update me if that help, but if not just try flashing it back to you original bios and if the problem still exist..well it's RMA time..

 

[SplifPolitics]

Have you tried unlocking shaders with RBE?
<a href="http://www.techpowerup.com/downloads/1962/mirrors.php">RBE Here</a>
Load your BIOS into RBE and select 6970 shader count (under additional features, all the way to the right)

i've never used this method, but I've heard it works

that's what you called bad flashing..try it with RBE if the ATIWindlash fail..

Well, I just modded my current bios with RBE (6970 shaders pciked in RBE), Flashed it with RBE - PC starts up fine But in GPU-Z the shaders are still 1408.

 

[Ginnoskie]

Well, I just modded my current bios with RBE (6970 shaders pciked in RBE), Flashed it with RBE - PC starts up fine But in GPU-Z the shaders are still 1408.

Try to unsinstall and install driver..sometimes it would help but not much..