EVGA put out a second teaser of its flagship graphics card based on the GeForce RTX 2080 Ti, the K|ngp|n (Kingpin), following the first bite in December. This picture details the cooling solution even better. The cooler uses a combination of an all-in-one (AIO) liquid closed-loop-cooler (CLC) and a fan-heatsink. The CLC does the heavy lifting, with a pump-block over the GPU, and some of the heat offloaded from secondary heatisinks. A set of fin-stack heatsinks cool the memory and VRM areas, which are ventilated by a 100 mm fan. EVGA appears to be using relatively expensive materials such as copper, for its secondary heatsinks.

ZOTAC are preparing a RTX 2080 Ti rendition of their ArcticStorm branded graphics cards. The ArcticStorm branding comes as a way to differentiate ZOTAC's graphics cards that pack a pre-installed waterblock, and will thus allow fur ultra cool, ultra silent temperatures on NVIDIA's beast of a GPU. The first rendition of the ArcticStorm, watercooled branding came to life under ZOTAC's GTX 1080 Ti, if you'll remember - the design has become more complex, and more colorful.

The RTX 2080 Ti ArcticStorm should feature a 16+4 phases power design, thus allowing for higher overclocking capabilities. The ArcticStorm cooling has been aesthetically redesigned, making use of the company's Spectra 2.0 RGB lighting control system for per-LED adjustments based on user preference. Expect further details to be revealed during CES.

MSI is ready with a Lighting Z branded flagship graphics card based on the GeForce RTX 2080 Ti. While the company is rumored to launch the card at CES 2019, two pieces made their way to overclockers "Gunslinger" and "Littleboy." While there are no pictures of the card in one piece yet (with its cooling solution in place), there are plenty of its PCB. The large, spread-out PCB draws power from three 8-pin PCIe power connectors. A gargantuan 19-phase VRM conditions power for the GPU and memory, split between two portions of the PCB, on either side of the GPU.

The heatsink cooling the larger portion of the VRM takes up most of the vacant space over the rear end of the PCB. In addition to some finnage, this heatsink uses a flattened heat-pipe to spread heat pulled from the area over the DrMOS (indirect contact), to the tail-end of the heatsink. "Gunslinger" and "Littleboy" have each managed to overclock this card to Godlike GPU clock-speeds in excess of 2450 MHz, likely using exotic cooling, such as liquid nitrogen.

RGB LEDs are a thing of the past - why would you settle for that limited 16.7 billion colors when you can have those colors actually forming images? That seems to be the thought process behind Colorful's new RTX 2080 Ti RNG Edition, which brings to the table a full-color LCD display for that ultimate build peek (and pic) capability. This seems to be a very limited edition run for NVIDIA's (current; you know that will change) top of the line graphics card, and brings a new color scheme and detailing on just about every part of the graphics card.

The EU-specific brand of GALAX, KFA2 today rolled out its latest flagship graphics card in the old continent, the GeForce RTX 2080 Ti Hall of Fame (HOF). In true tradition of this brand extension, the card is all-white - including its cooler shroud, fans, back-plate, and the PCB. The custom-design PCB pulls power from a trio of 8-pin PCIe power connectors located at the tail-end of the card rather than on top of it, and conditions it using a 16+3 phase VRM, to support an out-of-the-box speed of 1635 MHz boost, which isn't much higher than the NVIDIA-reference 1545 MHz, but is probably set to leave you a lot of manual OC headroom to play with. The memory is unchanged at 14 Gbps (GDDR6 effective).

The cooling solution uses a large aluminium twin-stack heatsink to which heat drawn from the GPU is fed to the fin-stacks by six nickel-plated copper heat pipes that make direct contact at the base. Additional contact points in the heatsink pull heat from the memory chips and MOSFETs. Three 100 mm fans ventilate the heatsink. The top of the card features an LCD matrix display that can put out live monitoring of temperature, fan-speed, and voltages. When interfaced with an app, it can also put out other details such as clock-speeds and memory utilization. The back-light illumination to this display, along with an ornament on the back-plate, are RGB LED illuminated. The card features two BIOS ROMs switchable via a push-switch. Both BIOSes run the card at the same clock-speeds, however, the second BIOS ramps up power-limit and stiffens the fan-curve. Available now, the KFA2 GeForce RTX 2080 Ti HOF is priced at 1,899€ (including VAT).

After some leaks indicated that GIGABYTE was preparing a blower-style RTX 2080 Ti, the company has now officially unveiled it. The GIGABYTE AORUS Turbo RTX 2080 Ti feature a blower-style cooler with vapor-chamber, direct-touch technology trying to keep that monstrous, 754 mm² TU102 chip cool and quiet. Luckily, the chip is relatively power efficient, so the acoustic and thermal performance should be sufficient.

The GIGABYTE AORUS Turbo RTX 2080 Ti features a 1650 MHz core clock, and the other specs line up with what we've become used to with RTX 2080 Ti graphics cards (11 GB of GDDR6 memory at 14000 MHz). There's the typical 3x DisplayPort, 1x HDMI, and 1x USB Type-C for VirtuaLink. Expect this version of the RTX 2080 Ti to be near the bottom rung in terms of pricing, when it's available.

ASUS Republic of Gamers (ROG) today announced the ROG Strix GeForce RTX 2080 Ti OC Call of Duty : Black Ops 4 Edition graphics card, an exclusive limited-edition version that's restricted to a production run of just 500 units and available only in selected territories. Decorated with the Call of Duty: Black Ops 4 Edition insignia, the card pairs the NVIDIA A-list GPU with gargantuan power delivery and cooling, and boasts out-of-the-box Boost clocks up to 1665 MHz to ensure performance stays silky smooth during frantic action.

ROG Strix GeForce RTX 2080 Ti OC Call of Duty : Black Ops 4 Edition keeps Turing cool by adopting a 2.7-slot design and devoting most of that real estate to a large heatsink that has 20% more surface area than previous-generation cards. The massive fin assembly allows completely passive operation during light gaming, and when active cooling is needed, it's provided by three IP5X-certified Axial-Tech fans developed specifically for the task. Featuring a smaller hub and longer blades surrounded by a barrier ring to increase structural integrity and static pressure, the new fans shift more air and generate less noise.

EVGA today released four new all-in-one (AIO) liquid VGA coolers for its GeForce RTX 20-series graphics cards, under its Hybrid Kit branding. The Hybrid Kit "400-HC-1184-B1" is meant for RTX 2080 and RTX 2070 XC, XC2, and Founders Edition variants. The "400-HC-1384-B1" is designed for RTX 2080 Ti Founders Editon and EVGA's XC and XC2 renditions of the RTX 2080 Ti. Both these models are priced at USD $169.99. The "400-HC-1284-B1" is designed for FTW3 series cards based on the RTX 2070 and RTX 2080; while the "400-HC-1484-B1" is meant for the RTX 2080 Ti FTW3. Both these FTW3 variants are priced at $179.99.

These coolers earn their "Hybrid" name in being a combination of liquid and air cooling. An AIO pump-block pulls heat from the GPU, while a heatsink ventilated by a 100 mm fan suspended along a shroud cools the VRM areas of the graphics cards. A base-plate covers the memory areas, and transfers heat to the AIO block. A 120 mm radiator along with a 120 mm PWM fluid-bearing fan dissipate heat drawn from the GPU and memory. The shroud covering it all is studded with addressable RGB LEDs that plug into the aRGB header of the PCB.

EVGA has been launching a number of products in partnership with renowned overclocker KIngpIn (Vince Lucido). These are typically made for extreme overclocking scenarios, and represent the very top of EVGA's offerings in terms of materials, build quality, and scarcity of built cards. For now, there's just a simple tease, posted via Vince Lucido's Instagram account, but this serves to surprise virtually nobody: NVIDIA's Turing will also receive the KIngpIn treatment.

Past examples of KIngpIn-branded graphics cards supported features such as improved power delivery systems (increased number of phases and power connectors), as well as some of the most versatile designs ever, with both triple-slot cooling solutions and single-slot adapters. As always, expect the GPUs inside the KIngpIn RTX 2080 Ti to be cherry-picked versions out of EVGA's crops.

Building upon the already popular EVGA GeForce RTX 20-Series cards and customizable Trim Kits, EVGA now offers a limited-edition Carbon Fiber Shroud and Carbon Trim Kit as the next step to make your EVGA graphics card stand out. Made with 100% real Carbon Fiber, EVGA is kicking off its latest RTX Accessories by giving away some Carbon Fiber Shrouds and Carbon Trim Kits to EVGA GeForce RTX 2080 Ti FTW3 and 2080 FTW3 purchasers. For a limited time, you can enter for a chance to win either a Limited Edition Carbon Shroud or Carbon Trim Kit for your EVGA GeForce RTX 2080Ti FTW3 or RTX 2080 FTW3 graphics card.

GIGABYTE looks to expand their NVIDIA GeForce RTX 2080 Ti lineup with the AORUS Turbo. This new offering features a blower-style cooler with a plastic shroud and no backplate. Considering the AORUS brand is typically enthusiast focused along with the fact GIGABYTE themselves already offer an RTX 2080 Ti with a blower-style cooler makes the AORUS Turbo a bit of a head-scratcher. Comparing the two shows the plastic shroud has been altered, however, outward appearance aside it is likely that the AORUS Turbo uses the same cooler as the GIGABYTE RTX 2080 Ti Turbo, which features a large vapor chamber cooler paired with a high-efficiency aluminium heatsink.

Meanwhile, power delivery is handled by two 8-pin PCIe connectors which are the standard for RTX 2080 Ti graphics cards. Display connectivity consists of three Displayport connectors, one HDMI connector, and a USB-C connector with VritualLink support. Other than that, full specifications and pricing are currently unknown. However, it can be speculated that the AORUS Turbo RTX 2080 Ti will feature stock clocks of 1545 MHz on the core and 14000 MHz on the memory with a price that should be close to MSRP at least in theory.

EA-DICE and NVIDIA earned a lot of bad press last month, when performance numbers for "Battlefield V" with DirectX Raytracing (DXR) were finally out. Gamers were disappointed to see that DXR inflicts heavy performance penalties, with 4K UHD gameplay becoming out of bounds even for the $1,200 GeForce RTX 2080 Ti, and acceptable frame-rates only available on 1080p resolution. DICE has since been tirelessly working to rework its real-time raytracing implementation so performance is improved. Tomorrow (4th December), the studio will release a patch to "Battlefield V," a day ahead of its new Tides of War: Overture and new War Story slated for December 5th. This patch could be a game-changer for GeForce RTX users.

NVIDIA has been closely working with EA-DICE on this new patch, which NVIDIA claims improves the game's frame-rates with DXR enabled by "up to 50 percent." The patch enables RTX 2080 Ti users to smoothly play "Battlefield V" with DXR at 1440p resolution, with frame-rates over 60 fps, and DXR Reflections set to "Ultra." RTX 2080 (non-Ti) users should be able to play the game at 1440p with over 60 fps, if the DXR Reflections toggle is set at "Medium." RTX 2070 users can play the game at 1080p, with over 60 fps, and the toggle set to "Medium." NVIDIA states that it is continuing to work with DICE to improve DXR performance even further, which will take the shape of future game patches and driver updates.A video presentation by NVIDIA follows.

NVIDIA today released the latest version of GeForce software suite. Version 417.22 refines optimization for "Battlefield V," with specific game-ready tuning for Battlefield V Tides of War Chapter 1: Overture Update. The drivers also introduce fixes to a number of bugs, including display corruption noticed on some high refresh-rate monitors connected via DisplayPort, and a blank screen noticed on BenQ ZOWIE XL2730 monitors when the refresh-rate is set to 144 Hz. A game crash noticed on "Hellblade" with RTX 2080 Ti is also addressed. Also fixed are incorrect memory clock speed reporting, and incorrect application of RGB color formats in NVIDIA Control Panel.DOWNLOAD: NVIDIA GeForce 417.22 WHQL

The change-log follows.

NVIDIA is ready with its new flagship halo consumer graphics card, the TITAN RTX. Several video bloggers such as LinusTechTips have apparently already been sampled with this card, and are probably under NDA not to reveal specifications. Given that "Turing" is the only NVIDIA architecture capable of RTX, NVIDIA could be building the TITAN RTX on the largest "TU102" silicon. The GeForce RTX 2080 Ti does not max out this silicon, leaving NVIDIA room to do so with the TITAN RTX.

A maxed out "TU102" should feature 4,608 CUDA cores, 288 TMUs, 96 ROPs, in addition to 576 tensor cores and 72 RT cores. NVIDIA could also max out the 384-bit wide GDDR6 memory bus, and equip the TITAN RTX with 12 GB of video memory. Using 14 Gbps GDDR6 memory chips, NVIDIA can achieve 672 GB/s of memory bandwidth. The TITAN RTX card itself looks similar to the RTX 2080 Ti Founders Edition graphics card, but with an illuminated "TITAN" logo on top. The card still draws power from a pair of 8-pin PCIe power connectors, and it's likely that NVIDIA is using the same PCB, perhaps with additional capacitors. Pricing and availability is anyone's guess. Given that the RTX 2080 Ti Founders Edition was launched at $1,200, we agree with some of our community members' speculation that $1,800-2,000 doesn't seem implausible.

Update Dec 3: The Titan RTX has launched now for $2,499.

Port Royal is the name of the latest component of UL Benchmarks 3DMark. Designed to take advantage of the DirectX Raytracing (DXR) API, this benchmark features an extreme poly-count test-scene with real-time ray-traced elements. Screengrabs of the benchmark depict spacecraft entering and leaving mirrored spheres suspended within a planet's atmosphere, which appear to be docks. It's also a shout out to of a number of space-sims such as "Star Citizen," which could up their production in the future by introducing ray-tracing. The benchmark will debut at the GALAX GOC Grand Final on December 8, where the first public run will be powered by a GALAX GeForce RTX 2080 Ti HOF graphics card. It will start selling in January 2019.

GIGABYTE debuted liquid-cooled WaterForce editions of its Aorus Xtreme GeForce RTX 20-series graphics cards early November, with three products, two based on the RTX 2080, and one RTX 2080 Ti. While the RTX 2080 got two variants, one featuring an AIO liquid cooling solution, and another with a full-coverage water-block for DIY liquid cooling; the RTX 2080 Ti at the time only released in the full-coverage water-block trim, with no variant that has an AIO CLC. GIGABYTE changed that today, with the new "N208TAORUSX W-11GC," or Aorus GeForce RTX 2080 Ti Xtreme WaterForce.

This card features a slightly spruced up version of the Asetek-sourced AIO closed-loop liquid cooling solution its RTX 2080-based sibling features, with a larger base-plate to draw heat from the additional memory chips and MOSFETs that come with the RTX 2080 Ti. The card features the same factory-overclock as the water-block equipped twin, with a GPU Boost frequency set at 1770 MHz (vs. 1545 MHz reference). The memory is overclocked to 10140 MHz (GDDR6-effective, vs. 14000 MHz reference). The cooler features RGB LED embellishments along the front, top, back-plate, and the two included 120 mm fans for the radiator. It draws power from a pair of 8-pin PCIe power connectors. Display outputs include three each of HDMI 2.0b and DisplayPort 1.4, and a VirtualLink port. The card could be priced upward of $1,400.

GIGABYTE, like most manufacturers of graphics cards, bet hard in the crypto craze to fuel demand for their graphics card solutions - an easy deal, considering the company is an AIB to both AMD and NVIDIA, which means they would cater to all of the cryptocurrency mining market. According to DigiTimes, market watchers are aware of the inventory buildup on GIGABYTE's watch, and cite the recent production issues with NVIDIA's latest RTX 2080 Ti graphics cards as reasons for the company to leave the black and cross the profit threshold towards a loss on the Q4.

GIGABYTE's Q3 was already reported as being a close cut in the earnings department, where the company didn't post losses simply because of non-operating incomes - meaning that inventory sold wasn't enough to offset all costs associated with bringing their products to market.

NVIDIA, via a blog post on its forums, has confirmed widespread reports of failures affecting their flagship RTX 2080 Ti graphics card. The issues, which resulted in "crashes, black screens, blue screen of death issues, artifacts and cards that fail to work entirely," started cropping up throughout tech forums, before reaching a critical mass that warranted coverage - just in case this was exactly what it seemed, ie, a production issue.

It seems this was just so, and that the problem was luckily limited to some early manufacturing issues or QA controls. As NVIDIA themselves put it, "Limited test escapes from early boards caused the issues some customers have experienced with RTX 2080 Ti Founders Edition." The company then says that they stand ready to help customers who are experiencing problems - but nothing else was to be expected, really.

Having survived an excruciatingly slow patch update, we are testing "Battlefield V" with DirectX Ray-tracing and NVIDIA RTX enabled, across the GeForce RTX 2070, RTX 2080, and RTX 2080 Ti, augmenting the RTX-on test data to our Battlefield V Performance Analysis article. We began testing with a GeForce RTX 2080 Ti graphics card with GeForce 416.94 WHQL drivers on Windows 10 1809. Our initial test results are shocking. With RTX enabled in the "ultra" setting, frame-rates dropped by close to 50% at 1080p.

These may look horrifying, given that at its highest setting, even an RTX 2080 Ti isn't able to manage 1080p 120 Hz. But all is not lost. DICE added granularity to RTX. You can toggle between off, low, medium, high, and ultra as "degrees" of RTX level of detail, under the "DXR ray-traced reflections quality" setting. We are currently working on 27 new data-points (each of the RTX 20-series graphics cards, at each level of RTX, and at each of the three resolutions we tested at).

Update: Our full performance analysis article is live now, including results for RTX 2070, 2080, 2080 Ti, each at RTX off/low/medium/high/ultra.

Thermaltake today introduced the Pacific V-RTX 2080 and Pacific V-RTX 2080 Ti full-coverage water blocks for ASUS ROG Strix series graphics cards based on the GeForce RTX 2080 and RTX 2080 Ti, respectively. These blocks are tailor-made for ASUS' custom-design PCBs for these cards, with heat-drawing bumps at just the right places, over memory and VRM MOSFETs. The blocks combine a nickel-plated copper primary material with a clear-acrylic top that has a stainless steel plate along the edge of the channel. A brushed metal finish back-plate also comes included. The top is studded with addressable RGB LEDs that can be controlled via ASUS Aura Sync RGB software. Both blocks come with mounts for standard G 1/4" fittings. The company didn't reveal pricing.

Today, NVIDIA released their GeForce 416.81 drivers, which among others, contains the following changelog entry: "[Turing GPU]: Multi-monitor idle power draw is very high. [2400161]". Back at launch in September, Turing was plagued with very high non-gaming power consumption, in both single-monitor and multi-monitor idle.

The company was quick to fix single-monitor power consumption, which we tested promptly. Unfortunately, at the time, multi-monitor power draw wasn't improved and people were starting to get worried that there might be some kind of unfixable issue present on Turing that would prevent NVIDIA from fixing multi-monitor power draw.

As a follow up to last week's all-in-one liquid cooling based product, GIGABYTE today released the Aorus Xtreme GeForce RTX 2080 Ti and RTX 2080 WaterForceWB. These cards are targeted at enthusiasts with DIY liquid cooling setups, and come with a factory-fitted full-coverage water block, instead of the AIO cooler. The block's primary material is nickel-plated copper with mirror finish, while its top is mainly acrylic, with opaque embellishments, a part of which is an addressable RGB LED diffuser that takes input from a standarized aRGB header. The opaque portion of the top also features a glowing Aorus logo.

The underlying PCB of the RTX 2080 Ti WaterForce WB packs a 16+3 phase VRM that draws power from a pair of 8-pin PCIe power connectors, 1770 MHz GPU Boost frequency, and a memory overclock of 14140 MHz (vs. 14000 MHz). The RTX 2080 WaterForce WB features the same PCB as its AIO-equipped twin, with a 12+2 phase VRM, 1890 MHz GPU Boost, and 14140 MHz memory OC. While the block itself is around 1-slot thick, a second row of display connectors makes the card 2-slot. Among these connectors are three each of DisplayPort 1.4 and HDMI 2.0b, and VirtualLink.

It has been been making the rounds now on various forum sites (including our own TPU) that problems have been cropping up for users of NVIDIA's Turing-based architecture graphics cards. The reports, which are increasing in number as awareness of the issue increases, vary in their manifestation, but have the same result: "crashes, black screens, blue screen of death issues, artifacts and cards that fail to work entirely," as reported by the original Digital Trends piece.

Of course, at the time, problems with the source for the information were too great to properly discern whether or not this issue stood beyond the usual launch issues and failures that can (and will happen) to any kind of hardware. The fact that people with negative experiences would always be more vocal than those without any problem; the fact that some accounts on the reported forums were of doubtful intent; and that the same user could be posting across multiple forums would always put a stop to any serious measurement of the issue. Now, though, NVIDIA has come out with a statement regarding the issue, which at least recognizes its existence.

Well this here is something that we don't see every day (read, never): an RTX 2080 Ti graphics card for $999. NVIDIA did announce pricing starting at that value for this particular graphics card, but pricing, as always with NVIDIA's Founder Editions, has always creeped towards the company's self-set $1,199. EVGA, however, has just put up a product page for their GeForce RTX 2080 Ti BLACK EDITION GAMING, a dual-fan solution (much like NVIDIA's own Founders Edition) with EVGA's iCX 2 cooling expertise that's being marketed at the unicorn-like $999 price-point, with a limit of 1 per household.

GIGABYTE today released an updated graphics card BIOS for its GeForce RTX 2080 Ti Gaming OC / WindForce OC (GV-N208TWF3OC-11GC) graphics card, with significantly increased power limits. The card originally ships with a power-limit adjustment headroom of up to of 290 Watts. The new BIOS increases that all the way up to 366 W. The default power limit for both BIOSes is 260 W, so you'll have to use GIGABYTE's Aorus Engine utility to increase the power limit manually to 366 W instead of 290 W.

The increased power limit helps the card sustain its GPU Boost frequencies better, since there is more electrical headroom. The new BIOS, however, don't tinker with temperature limits. 84°C is still the temperature at which the GPU will begin to lower clock speeds to bring down temperatures, and 88°C is the temperature limit. GPU Boost uses a combination of factors such as utilization, power limit, and temperature to increase GPU clock speeds, to increase performance. You can find both the new BIOS, and the original BIOS for this card below. You use the BIOS at your own risk.DOWNLOAD: GIGABYTE High Power Limit RTX 2080 Ti BIOS | GIGABYTE RTX 2080 Ti Gaming OC Original BIOS