Saturday, October 1st 2022
The USB-IF Announces New Logos, Kills Off SuperSpeed Branding
The USB Implementers Forum (USB-IF) has announced a few changes to the various logos that are tied to the USB standard. This is said to be done to simplify the plethora of logos that are currently being used and to make it easier for consumers to know what they're buying. At the same time, the old SuperSpeed USB logo is being retired and the branding will not appear on new products at all. Instead, the logos that were developed for the USB4 standard and USB PD 3.1, will be adapted across the board. The new changes will come into effect this quarter and could appear on new products before the end of the year.
The new logos that will replace the SuperSpeed logo are pretty straightforward, with a 5 and 10 Gbps logo being added to the 20 and 40 Gbps logos that we've already seen. These logos will be used for packaging, on cable connectors and even on some devices. The new 5 and 10 Gbps logos can also be combined with the 60 W and 240 W charging logos when used with USB-C cables. All of this should make it easier as a consumer to know what kind of cable you're buying, but keep in mind that these logos only apply to certified products and not all USB cables are certified. Still, it's an improvement overall and should make life easier when shopping for cables, assuming the new logos are being used properly.
Sources:
The USB-IF, via The Verge
The new logos that will replace the SuperSpeed logo are pretty straightforward, with a 5 and 10 Gbps logo being added to the 20 and 40 Gbps logos that we've already seen. These logos will be used for packaging, on cable connectors and even on some devices. The new 5 and 10 Gbps logos can also be combined with the 60 W and 240 W charging logos when used with USB-C cables. All of this should make it easier as a consumer to know what kind of cable you're buying, but keep in mind that these logos only apply to certified products and not all USB cables are certified. Still, it's an improvement overall and should make life easier when shopping for cables, assuming the new logos are being used properly.


66 Comments on The USB-IF Announces New Logos, Kills Off SuperSpeed Branding
I guess if you needed bleeding-edge data transfer rates you probably would have cared but the USB standard has always been at least an order of magnitude faster than the fastest devices you'd typically expect to connect over USB.
When 10Gbps USB was released in 2013, the fasted drives you could possibly get were SATA-based and it was rare outside of synthetic sequential testing that any of those drives could saturate the old 5Gbps bandwidth.
Now with 80Gbps USB you are unlikely to find any device on the market that can reliably use that bandwidth. PCIe Gen5 SSDs in an enclosure could theoretically do it, but the USB-to-PCIe bridge chip doesn't yet exist, and first-generations of it are likely to suck, like they always do. It's genuinely hard to find an external drive that can read at more than about 25Gbps and that's if you spend silly money on overpriced external drives.
Basically, as long as you're using the fastest port on your device with the latest device, you're generally going to be fine, whatever the hell they label it as; Real-world hardware always trails behind the current-gen platforms by enough that it's almost never an issue - and when it is an issue, you have to truly ask whether the limitation is the USB interface bandwidth, or if it's something more primitive like running out of pSLC cache, performance loss in the PCIe-to-USB controller, lack of HMB since the USB controller can't transparently pass through PCIe/NVMe etc. There are countless reasons why a USB device is slower than something connected directly to the CPU via PCIe and until USB becomes a physical hot-swappable PCIe connector, it will always be subject to extra steps that slow it down.
the 10GB/s of 80Gb, is going to split nicely with a USB-C hub that works for a 10Gb ethernet adaptor, an NVME drive and some regualr 5Gb ports
For the sake of one additional cable I'd rather just have a display out via HDMI (and the MUX chip) rather than going over Thunderbolt/USB-C
Single-cable convenience will be a deciding factor for some people, I'm sure....
Hubs or docks (docking stations) may be necessary if your primary system is a laptop. I agree, most hubs are garbage and have misleading marketing, finding one with 10Gbps USB, HDMI 2.0 and/or even GbE takes time.
Direct HDMI connection - yes, unless OEM saved a few pennies on LSPCON and your card supports, say, HDMI 2.0 but your (laptop) port is 1.4 only; that's a common case. It makes USB-C to HDMI 2.0 adapter really useful.
5Gb is enough for a bajillion USB 2.0 peripherals, 80Gb would let me run my monitor off that connection too, which is just insane.
If you meant USB3 20gbps and USB4 20gbps, I was going to go into the rabbit hole but looked at this table from wikipedia and decided it was best to just give up (it seems to be about the same with a slightly different encoding - packages with half the size - but I don't know).
case in point I have a usb 3.2 gen 2x2 20port on my motherboard. A 20 Gbps port. But alpine ridge devices connected to this port do not enumerate or connect. Why? Because the port doesn’t support pcie tunneling or tb3 signaling. And since alpine ridge doesn’t have a usb3 fallback mode it must be connected to a tb3 or usb4 port to connect. The ambiguous label “20 gbps” does nothing to tell me if my alpine ridge device will work with the port, or not.
The fact that Intel is trying to sell Thunderbolt as USB is their marketing problem, not that of the USB standard.
Wiki pages are stating that due to the tunneling some overheads are reduced so say an NVME SSD on 20Gb/s 4.0 should be still faster than 20Gb/s 3.x
This likely falls on the motherboard manufacturers and their shitty backplates with poor labelling, than anything else
(Although with how few USB-C ports we have, it'll likely be fairly obvious)
Intel fixed the problem with titan ridge and later, but still…