Tuesday, August 25th 2026

ASUS Unveils ROG Rapture GT-BN98, First Wi-Fi 8 Gaming Router

ASUS unveiled the ROG Rapture GT-BN98 at Gamescom 2026, presenting it as the world's first Wi-Fi 8 gaming router. The ROG Rapture GT-BN98 is a quad-band Wi-Fi 8 (802.11bn Draft) router featuring eight distinctive external antennas, giving it a menacing look. It uses a quad-core processor running at 2.6 GHz, 256 MB of flash, and 2 GB of RAM. The router's total throughput goes up to 25,000 Mbps. The 2.4 GHz band reaches up to 1,376 Mbps, both 5 GHz bands hit 5,764 Mbps each, while the 6 GHz band features up to 11,529 Mbps with 320 MHz channel support. Wired connectivity includes one 10G WAN/LAN port, one 10G LAN port, one 2.5G WAN/LAN port, three 2.5G LAN ports, and one standard gigabit LAN. The routers also have USB 3.2 Gen 1 and USB 2.0 ports, and support Router, AiMesh node, Access Point, Repeater, and Media Bridge operating modes.

On the software side, Adaptive QoE handles dynamic bandwidth allocation based on live network conditions while Wi-Fi Insight monitors all bands in real time with continuous interference detection running in the background. Moreover, ASUS bundled GTNet, a third-party service that routes game traffic through the most reliable path to game servers. For security, we have AiProtection that also includes ad and tracker blocking. Guest Network Pro supports up to five SSIDs for IoT management, VPN, and parental controls. No pricing has been announced.
Source: ROG Rapture GT-BN98 (product page)
Add your own comment

42 Comments on ASUS Unveils ROG Rapture GT-BN98, First Wi-Fi 8 Gaming Router

#26
Hoak
TheLostSwedeOne thing everyone seems to forget in the discussion of pros and cons when it comes to Wi-Fi vs. Ethernet is that Wi-Fi is half duplex, whereas Ethernet is full duplex, which can make a huge difference if you need to send and receive data at the same time.
Eyup! Full-duplex, vastly lower latency, less packet loss, and none of the vast array of security issues (that securing also add transmission over-head) Wi-Foo is for Eloy...
Posted on Reply
#27
MikOnTopGG
HoakEyup! Full-duplex, vastly lower latency, less packet loss, and none of the vast array of security issues (that securing also add transmission over-head) Wi-Foo is for Eloy...
This is why I bought a RJ-45 CAT6 cable for 25 dollars.
Posted on Reply
#28
Hoak
MikOnTopGGThis is why I bought a RJ-45 CAT6 cable for 25 dollars.
You can buy ghetto-most CAT5 Cable for 1/10 that, and still be out-performing the most SOTA Wi-Fud setup... But even the most exotic CAT* cable, is not that big a hassle to run -- will future, headache, and nightmare proof any home or SOHO setup and is still cheap by comparison...
Posted on Reply
#29
TheLostSwede
News Editor
CheeseballNot really. It's all situational. You can have a house that can has minimal wireless signal blockage (usually houses with internal walls help up with wooden studs) BUT you may not have cable runs in the walls to accommodate Ethernet cables going to each room. You only need to have this router connected to the ONT/modem that either the ISP or yourself provide.

Quad-band, so one 2.4GHz, two 5GHz and one 6GHz. Two 10Gbps ports, three 2.5Gbps and one 1Gbps? @TheLostSwede Do you know what chipset combination this is that has such an awkward Ethernet configuration?
Ok, it might be the newer BCM4918.




www.broadcom.com/products/wireless/wireless-lan-infrastructure/bcm4918
Posted on Reply
#31
Bagerklestyne
Here's a question/thought for @TheLostSwede and the brains trust.

Why not have 10g ports and go, here's a lump of bandwidth, you decide how you want it divided. Increased costs a little but the ability to go, I need 3x 10g lan ports, and 1g wan, then later on, tweak to revise 10g wan, maybe drop a secondary 10g lan port to 5g.

I mean the wan might be locked out potentially but since the lan ports are hanging off the same chip surely being able to min max ports as you see fit would provide some use cases to end users.
Posted on Reply
#32
TheLostSwede
News Editor
BagerklestyneHere's a question/thought for @TheLostSwede and the brains trust.

Why not have 10g ports and go, here's a lump of bandwidth, you decide how you want it divided. Increased costs a little but the ability to go, I need 3x 10g lan ports, and 1g wan, then later on, tweak to revise 10g wan, maybe drop a secondary 10g lan port to 5g.

I mean the wan might be locked out potentially but since the lan ports are hanging off the same chip surely being able to min max ports as you see fit would provide some use cases to end users.
And how do you suggest this is meant to work? A port is whatever speed the MAC and the PHY allows for. The higher the speed of the port, the more the parts costs.

This is like saying why don't all PCs have PCIe 6.0 lanes only, as you can always go slower if you don't need that speed.
Posted on Reply
#33
Grimling
I have 14 ms latency to a Server on Ethernet, and 44ms over Wifi.
Guess what i am gonna use for gaming...ASUS...
Posted on Reply
#34
Bagerklestyne
TheLostSwedeAnd how do you suggest this is meant to work? A port is whatever speed the MAC and the PHY allows for. The higher the speed of the port, the more the parts costs.

This is like saying why don't all PCs have PCIe 6.0 lanes only, as you can always go slower if you don't need that speed.
I wrote, rewrote, and rewrote again. Seems I'd like the expansion interconnects to be pcie4 not 3 so that a 10g option would be available. Looking at the chipset diagram you put in above, the pcie controllers appear to be all pcie3 which is capped at under 8gbit, maybe when (if/when) we move to these then 10g will be an option without esoteric add on cost.

From what I can read the dedicated 10g lan 'gaming port' is an add-in chip in addition to the BCM4918, so I have no idea what they're worth (100 ?).

Hell let's make them lego and I can plug in what I want.

I can dream can't I ?
Posted on Reply
#35
TheLostSwede
News Editor
GrimlingI have 14 ms latency to a Server on Ethernet, and 44ms over Wifi.
Guess what i am gonna use for gaming...ASUS...
Give this a go, if you want to test your real latency.
www.waveform.com/tools/bufferbloat
BagerklestyneI wrote, rewrote, and rewrote again. Seems I'd like the expansion interconnects to be pcie4 not 3 so that a 10g option would be available. Looking at the chipset diagram you put in above, the pcie controllers appear to be all pcie3 which is capped at under 8gbit, maybe when (if/when) we move to these then 10g will be an option without esoteric add on cost.

From what I can read the dedicated 10g lan 'gaming port' is an add-in chip in addition to the BCM4918, so I have no idea what they're worth (100 ?).

Hell let's make them lego and I can plug in what I want.

I can dream can't I ?
10 Gbps Ethernet can be done over two PCIe 3.0 lanes, so no issue there, but when it comes to routers, PCIe is usually not used for Ethernet, instead it's some kind of media-independent interface (MII) that is being used, in this case USXGMII (Universal Serial 10GE Media Independent Interface) for 10 Gbps.

It's also cheaper to just use a PHY, as the MAC is built into the SoC.

I don't know what Broadcom charges, but I have an idea what Realtek wants and we're talking less than $10 per 10 Gbps chip, the ones that have a MAC and a PHY and normally goes on a network card. A PHY is normally around half that cost.
Even Aquantia, that Broadcom bought to get competitive 10 Gbps solutions, was only charging $40-50 for their single chip solutions and that was the original AQC107 which was more costly to produce than the current AQC113.
Posted on Reply
#36
ZeDestructor
BagerklestyneHere's a question/thought for @TheLostSwede and the brains trust.

Why not have 10g ports and go, here's a lump of bandwidth, you decide how you want it divided. Increased costs a little but the ability to go, I need 3x 10g lan ports, and 1g wan, then later on, tweak to revise 10g wan, maybe drop a secondary 10g lan port to 5g.

I mean the wan might be locked out potentially but since the lan ports are hanging off the same chip surely being able to min max ports as you see fit would provide some use cases to end users.
BagerklestyneI wrote, rewrote, and rewrote again. Seems I'd like the expansion interconnects to be pcie4 not 3 so that a 10g option would be available. Looking at the chipset diagram you put in above, the pcie controllers appear to be all pcie3 which is capped at under 8gbit, maybe when (if/when) we move to these then 10g will be an option without esoteric add on cost.

From what I can read the dedicated 10g lan 'gaming port' is an add-in chip in addition to the BCM4918, so I have no idea what they're worth (100 ?).

Hell let's make them lego and I can plug in what I want.

I can dream can't I ?
The answer is simple: it's hard-bound in the silicon - there's 2 10G ports, distributed through the two USXGMII ports (and likely with a weird dual-port controller), then you have 1 2.5G WAN and 3 2.5G LAN. For those 2.5G ports, the PHYs have been integrated directly on the chip in order to save money (by not having to buy and install seperate PHYs). The PCIe lanes, meanwhile, are simply not available for further ethernet expansion, since those are used to linkup to the wifi radios. Additional to that, on devices like these, the networking engine is implemented in hardware, so you can't easily add more ports using PCIe NICs, since that would generate a lot of CPU load that the CPU in the thing would not be capable of handling.

The "right" way to add more ports is to add a switch, as Igb discovered, especially given the limitations related to the 10G ports.
Posted on Reply
#37
remixedcat
Let3rIf you are serious about gaming, why would you use wifi and not Ethernet? Also, I’m still on wifi 5 and it is perfectly fast.
Even on 802.11ax the max wireless transfer speeds over SMB shares from the system in my specs to the precision 3550 in my signature was 50MBps. (intel ax201, over the alta AP6 AP)
Broken ProcessorThe ironic thing about gaming routers is they are faster and rmore reliable with the gaming features turned off.
Yes, most of those will put your networking processes on a dedicated chipset that's often not made for huge loads like offsite backups, huge game/file transfers, etc due to something called "bufferbloat" and it might be faster for burst transfers but those huge ones will bring your network to its knees, if implmented badly. Best to turn those features off and set standard QoS manually instead and disable hw acceleration so it uses the beefier main SoC for network processing.
kazuvikingDepends if Merlin can be installed on it.
hard with it using a broadcom SoC broadcom is the worst for open source support and has gotten worse w time.
Posted on Reply
#38
Razor512
Broken ProcessorThe ironic thing about gaming routers is they are faster and rmore reliable with the gaming features turned off.
That is often because the gaming focused features are often gimmicks or require significant compromises. For example, most buffer bloat solutions often involve the router detecting game traffic and then capping speeds so that you do not fully saturate the WAN connection. That works well to prevent latency spikes, but what many people end up seeing is that the game mode restrictions need to be bet based on the lowest speeds your connection is expected to get during heavy congestion. If you have an extremely consistent WAN connection, then those features often work well if someone needs to game while someone else downloads lots of linux ISOs. On the other hand, if someone has a highly variable cable connection, then they are often unable to find a single good setting.
Beyond that, no one seems to have found a way to make it so that the router can analyze the traffic and look for signs of buffer bloat and dynamically adjust how close clients can get to saturating the WAN.
Posted on Reply
#39
remixedcat
If they used something like CAKE to do that but must of these brands don't tell you what they use
Posted on Reply
#40
ZeDestructor
remixedcatIf they used something like CAKE to do that but must of these brands don't tell you what they use
fq_codel is the most common these days I want to say, but ultimately the one true solution is to limit your speed to a little below what the line/connection can achieve. For those of us with a decent ISP, this is trivial. For those with wildly varying speeds throughout the day, much tougher.
Posted on Reply
#41
remixedcat
ZeDestructorfq_codel
That's what ubiquiti uses along with something else too

ok i found it it's HTB + fq_codel.
Posted on Reply
#42
AleXXX666
Harun8Running a very long cable through your house is a massive pain and hassle, but it saves a ton of money and will be better. I can't imagine being rich enough to invest hundreds on a router and not a $30 cable and 2 hours of work
plus you will have to install shitty repeaters ("mesh" shit) here and there otherwise you will have that stupid "dead zone" in some toilet/kitchen/bathroom etc. lmfao;):D
Posted on Reply
Add your own comment
Nov 19th, 2026 21:34 CST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts