Tuesday, July 7th 2015

Sapphire Radeon R9 Fury Pictured, Specs Confirmed

Here are some of the first pictures of Sapphire's custom-design Radeon R9 Fury graphics card. The card features a triple-slot (or 2.2-slot) Tri-X cooling solution. Its PCB appears to be AMD reference-design (identical in design to the R9 Fury X), but cooled by a long triple-fan dual-stack heatsink, with over one-third of it being overhung. Quite a few GTX 970, GTX 670, and GTX 760 cards are known to have similar overhangs of coolers that are longer than the PCB.

The pics also come with leaked specs-sheets, which confirm its core configuration of 56 out of 64 compute units being enabled, yielding 3,584 stream processors; while leaving the 4 GB 4096-bit HBM memory untouched. The core clock speed is lower, at 1000 MHz, while the memory clock is left untouched at 500 MHz, compared to the R9 Fury X. Sapphire is also selling a factory-overclocked card with 1040 MHz core. The Radeon R9 Fury is expected to launch in mid-July (next week).
Source: VideoCardz
Add your own comment

42 Comments on Sapphire Radeon R9 Fury Pictured, Specs Confirmed

#27
2big2fail
brumak51the cooler....hmmm...


Sorry, I couldn't resist... :laugh:
Posted on Reply
#28
haswrong
the54thvoidYeah, and base clock 'up to' 1000 or 1040Mhz. Could signify known thermal throttling or playing it safe after Hawaii?
more like playing it foul.. fury (x) was supposed to be an overclocekr's wet dream according to amd's presentation..
Posted on Reply
#29
zzzaac
Going to be a bit of a squeeze on my case. Card is about ~12inches long
Posted on Reply
#30
TheinsanegamerN
LightningJRI find cooler overhangs funny, my 670 is the same, the whole blower fan hangs off the end of the card. Just goes to show how small electronic parts are becoming.

I do wonder if the 3 slot (2.2 wide) hs/f is REQUIRED, I wasn't a fan of 2 slot coolers but at least you can properly do sli/cf with them.

I sincerely hope a 3 slot is not required because of the temps. We'll know soon. I guess we'll know how good the water cooler on the Fury X is.
Tri slot isn't REQUIRED, per say. the gigabyte, xfx, ece were all standard two slot. Sapphire hit a bit of a home run with the tri-x cooler on the 290x, making it one of the best performers.

The 390x cooler is very similar, and the fury cooler looks almost identical. Why change what isn't broke? going dual fury would probably benefit more from watercooling, and a full atx mobo usually has three spaces between the two primary pcie 3.0 slots, unless its a triple/quad gpu mobo.
fullinfusionOh lord, I was afraid of this. These chips do run super hot to have an extended cooled on the cards..

I'll personally be staying away from these fury cards unless water cooled. Everyone knows I love my crossfire systems but not this time.
It's not super extended, the card is about the same size as the 390x and 290x. It just looks bigger because the fury PCB is so small. There is also no proof these run super hot, probably around the 980ti level, given the power consumption of the fury x, and given that fury has 1/8th fewer shaders, power consumption will probably be around the level of a 290.
Posted on Reply
#31
Sir Alex Ice
Petey PlaneYou should look at the pictures. The dimensions of the card are listed. "306(L)*114(W)*49(H) mm"
You are right, did not notice them, probably the font was too big and too bold. Less than 310mm makes it compatible with lots of decent cases, best it would be to have one with fans in the side panel to help with cooling that over 250W of power used.
Posted on Reply
#32
ZeppMan217
So, the third fan doesn't actually do anything?
Posted on Reply
#33
tomkaten
ZeppMan217So, the third fan doesn't actually do anything?
????

Are we suddenly under the impression that a fan needs to blow through the radiator directly into the card ? Fans are there to cool the HS fins, not any components directly.
Posted on Reply
#34
mroofie
john_Sapphire just took the best cooler they have and throw it on the card. If they where creating a different cooler for R9 Fury , I wouldn't be surprised to see posts saying that "I am waiting for the Tri-X version".

At least they didn't do something like this

Wow you reek of fanboy :rolleyes:

:slap:
Posted on Reply
#35
john_
mroofieWow you reek of fanboy :rolleyes:

:slap:
So many arguments in your post, I don't know where to start.
Posted on Reply
#36
Haytch
Petey PlaneWhy would you have to add a water block? The heat sink and fan setup on that card looks more than adequate.
I would need to add the water block and cooling kit to reduce the heat of the GPU whilst under load as opposed to the heat-sink and fan setup, also, reduce the required dual slot space taken by the card and clear up that general area of the board.
Personally, I always seem to find a use for my remaining PCI-E slots. Ever since my 8800GTX back in the day, I have always water-cooled my GPU's and never looked back. Obviously before water-cooling I run a series of benchmarks to compare the heat-sink and fan setup with the water-cooled setup and my findings are always substantial enough to warrant the water-cooled option.
Posted on Reply
#38
ypsylon
Couple days back, as I can't browse internet much mon-fri. Still I have to say this. I hope they include 5.2.5" mounting bracket for this monstrosity. :D
Posted on Reply
#39
Unregistered
ypsylonCouple days back, as I can't browse internet much mon-fri. Still I have to say this. I hope they include 5.2.5" mounting bracket for this monstrosity. :D
Errrr.... wrong place maybe? :confused:
Posted on Edit | Reply
#40
Caring1
Mods, can this be locked now?
Posted on Reply
#41
Tatty_Two
Gone Fishing
It's a news article so no :)
Posted on Reply
Add your own comment
Nov 17th, 2026 14:37 CST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts