• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.
  • The forums have been upgraded with support for dark mode. By default it will follow the setting on your system/browser. You may override it by scrolling to the end of the page and clicking the gears icon.

Gigabyte GA-MA790X-UD4 Thread

Shadowdust: Interesting... Did you try tweaking NB and CPU-NB voltage? Maybe some increasing on NB and CPU-NB help you with CPU OC. Try CPU 1.425, CPU-NB +0.1 ( NB set do default speed - 2000MHz), NB 0.1V and RAM to 800 speed and loose timings. Then try to boot at 3.6 and do so stress testing - if CPU fail, try with more CPU voltage, if fail too you have probadly "ordinary" CPU nad over 3.5 dont go. I can do 3650 with 2600 NB, but 3720 isnt totally stable, but CB x64 and wprime is ok, but linx not. If you need fufther info please send me PM.
 
My NIC disappeared once too but I reset CMOS and all was fine.
 
Thanks for the info guys. :D If I ever decide to put the 940 back in my case, I'll try the settings you suggested, froxic. :) Currently, I'm using a PII 550 BE oc'd to 3.6 GHz on 1.40 vcore. Also, I was fortunate enough to unlock the other two cores with ACC.

When the NIC issue first started, I tried resetting the CMOS but no luck with everything returning to normal. What's interesting is that my router detects the port in gigabit mode. But when I check the cable status in the BIOS it says something about testing a virtual connection as if there is no connection. I may try resetting the CMOS again just to be sure.
 
Shadowdust said:
Well your OC is still better than what I could accomplish with a 940. I was only able to manage 3.5 GHz at 1.425 vcore. I could boot Windows at 3.6 GHz but within one minute of Prime95 stressing, I'd get a blue screen.

Has anyone had any ethernet issues? Recently, my ethernet disappeared in my Device Manager. At first I thought it was completely dead so I hooked it into an old 10/100 Linksys switch. When I would reboot, the ethernet would reappear. The moment I brought it back to my gigabit router though, it would disappear again. So I finally reduced the speed to 100 Mb and hooked it back to my gigabit router. It is recognized on that router now. I don't like being limited in my transfer speeds, so I recently purchased a cheap ethernet card. Anyway, it's really an annoying issue and I am quite curious if I'm the only one who has experienced this.
Click to expand...


my AIR x4 955 1.475V and 3.895 GHz stable, NB 2665 MHz;). I know some guys with 3.9 up or 4 GHz stable at AIR, but it with only x4 955 BE and x4 965 BE (better chips).
For x4 940 is mostly 3.6-3.7GHz stable.
 
FlanK3r said:
my AIR x4 955 1.475V and 3.895 GHz stable, NB 2665 MHz;). I know some guys with 3.9 up or 4 GHz stable at AIR, but it with only x4 955 BE and x4 965 BE (better chips).
For x4 940 is mostly 3.6-3.7GHz stable.
Click to expand...

Yep for 940 is common 3.6-3.7. 3.8 GHz is for best chips, and in your case 3.4-3.5 is for worst - but this is normal in overclocking that some chips are better then other. Anyway - 3.5 is 500 MHz difference and for free. I remember my first AMD rig with Athlon XP Palomino - i was very dissapointed, because i can overclock it from 1666 to 1700 and no further
 
guys, watch at this, this must be gold binned chip!

user blackwarriors, really only 1.375V !!! And AIR
1252057116.jpg


And 1.25V for boot to windows 4 GHz :eek::respect:

690661.png
 
very nice OC for 955 with that low voltages. But performence wouldnt be supreme instead of 2000 MHz NB clock. For 4GHz is 2800-3000 NB ideal. 2000 NB - thin bottle neck ( sorry for my expresions. Im not native speaker :) )
 
:-)
 
Hi, I'm currently with bios F3f.I want to try to unlock my Ph II 550 but I can't see the Hybrid mode in the BIOS.In the last few pages it was mentioned that in the BIOS I'm using this function is missing.So which BIOS do you recommend me?
I got my CPU to 3830MHz stable.It probably can do more but i'm not the best overclocker.Now I'm using it on default with Cool'n'Quiet enabled.
P.S. Sorry for my bad English. :(
 
Last edited:
You must push CTRL+F1 (maybe ALT+F1) in main bios scrren, then some hided parts of bios appear. Then go to ACC ( Advanced clock calibration ) page, and there is hybrid mode you wished. And you can be calm, in my opinion F3 has same OC cappabilities like F5, so you can stay at F3 version.
 
Stiliyan said:
Thanks, I've unlocked two cores but the CPU isn't stable.Prime95 shuts down after I start stress test and the AOD stress test stops immediately. :(
http://www.picvalley.net/v.php?p=u/2...3dK9LqMlOG.PNG
Click to expand...

No problem, but photo you posted is removed. There is still hope to make it stable. What clock youre traing for 4 cores? Default or your max OC speeds? Try default - when faul raise voltage - max 1.45V (for further increasing is needed extreme air cooling, water, dice, LN2, etc.

You can find worst core too if youre set afinity to core 1.. to core 4 in steps, then you can add more voltage with ACC to worst/faulty core indepedently to other cores.

Overclocking is hard work, but you can push it harder and maybe you can unlock to 4 stable cores after some tweaking ;)
 
On weekends Il try some Benchmarks: my point are:
Cinebench in x64 at 3.95 GHz
Superpi 32M: more than 4 GHz

all AIR cooling
 
FlanK3r said:
On weekends Il try some Benchmarks: my point are:
Cinebench in x64 at 3.95 GHz
Superpi 32M: more than 4 GHz

all AIR cooling
Click to expand...

I wish you luck. Superpi is possible at 4 GHz or more, but Cinebench X64 is nuts in 3.95. It will be mybe posible only in winter when youre put pc to the windows and keep it in freeze (im planing to do this) :D
 
froxic said:
No problem, but photo you posted is removed. There is still hope to make it stable. What clock youre traing for 4 cores? Default or your max OC speeds? Try default - when faul raise voltage - max 1.45V (for further increasing is needed extreme air cooling, water, dice, LN2, etc.

You can find worst core too if youre set afinity to core 1.. to core 4 in steps, then you can add more voltage with ACC to worst/faulty core indepedently to other cores.

Overclocking is hard work, but you can push it harder and maybe you can unlock to 4 stable cores after some tweaking ;)
Click to expand...
I've tried the CPU on default, on 2800MHz;2600MHz;2400MHz with 1.4V.The maximum voltages I put was 1.325+1.0V and there was no effect.I am with this cooler - http://www.arctic-cooling.com/catalog/product_info.php?cPath=1_43&mID=133&language=en
How can I set afinity to one of the cores?In the ACC I tried to put lower percents on the thirt and the fourth cores but with no success.
 
In taskmanager in windows, browse to process tab, then choose process that you want change affinity and right click on in and choose set affinity ...

affinity1.jpg


So when youre stress testing CPU, do it separately for each core

EDIT: ACC is none-related to CPU affinity, In ACC you can only increase or decrease CPU cores voltage separately. So for examle you find that core 4 is faulty and you have ACC setings +2 +2 +2 +2 on all cores, you put new settings +2 +2 +2 +4(+6) or somethink like that and you can pray that it will works. But first, try to boot at very low speeds, like 800 or 1000 MHz on CPU, when it will be unstable, i think you havent chance to stable it

EDIT2: Im hit my personal record in superII.



3919,6MHz - 17.628s
 
Last edited:
I will put the multiplier on 7(1400MHz) and in the AOD there is a function to test each core.Should I turn on the calculation and MCA test?
http://pics.data.bg/zoom/albums/7345bcdb486a61516997bffc7970c714
EDIT1 :I caught the bad core with the set affinity - CPU Core 0.
AOD confirmed that :
http://pics.data.bg/zoom/albums/ec0dbe5df15f8738212ad73f4a7253da
In ACC I will set +2(4/5/8/10);-2;-2;-2 on 1500/2000/2500MHz
EDIT2 :
It didn't work on +2/4/6/8/12/-2/-4/-8/-10.Can I stop one of the four cores?
 
Last edited:
Offtopic, but I think its pointless to add a new thread.

Question about 790GX-UD4H. Is the onboard audio any better than on DS4H? I thought there could possibly be less interference due the thicker copper layers...
 
790x-ud4 isnt dead...Great board
 
lol, youre still alive, arent you death instead benchmarkung? :toast:
 
not now :)...maybe later, today i was fighting with Cinebenchs run and wprime, but i forgot save wprime screens :( (32M 9.1s)
 
I have gone through 3 790x ud4s in the past 3 months, i have had a running time of about 1.5 weeks between them, the third one turned up DOA with a cpu pin in the socket and thermal paste on it.

They have now sent me a ud3p saying that they have changed it as they have had problems with the 790x ud4 model.
 
You must log in or register to reply here.
Back
Top