Monday, February 10th 2025

Unofficial 12V-2x6V Power Connector Melts NVIDIA GeForce RTX 5090

NVIDIA's high-TDP flagship GPU, the GeForce RTX 5090, appears to cause additional headaches for users, not including the high power bill. According to a Reddit user, we now have the first documented case of a melted power connector on NVIDIA's flagship GeForce RTX 5090 Founders Edition, reigniting concerns over high-wattage GPU safety from the last generation. While playing Battlefield 5, Reddit user ivan6953 detected a burning odor and immediately shut down their system, only to discover severe damage to both the RTX 5090's 12V-2×6 connector and their ASUS ROG Loki SFX-L PSU. The user had employed a Moddiy 12VHPWR cable, marketed as ATX 3.0/PCIe 5.0-compliant and rated for RTX 5090's 600 watts of power. Despite claims of secure installation—audible clicks at both ends—the cable melted at 500-520 W load, charring connectors on the GPU and PSU.

Notably, the same cable had powered an RTX 4090 FE for two years without issue. NVIDIA's RTX 5090 FE ships with a redesigned adapter featuring a longer, more flexible cable and an angled connector to reduce strain in compact builds. NVIDIA asserts that no incidents have occurred with its bundled adapter, emphasizing compliance with the updated 12V-2×6 standard, which shortens sensing pins to prevent power flow if connections loosen. Hence, an older connector can not provide 100% secure usage despite the user thinking that the sensing pins are touching properly.
A second case reported by Spanish YouTuber Toro Tocho involved a melted PSU-side connector, though the GPU remained undamaged. This resulted from worn connectors or improper seating despite user assurances of correct installation. RTX 5090 owners should avoid third-party adapters and rely solely on NVIDIA's included cable or PSU-native connectors. Regular inspections for discoloration, wear, or bending near connectors are also advised, particularly for systems with high power consumption. While NVIDIA investigates, the takeaway is clear: cutting corners on power delivery risks costly hardware failures. The RTX 5090's melting woes appear isolated to unofficial accessories—a small solace for early adopters navigating the pitfalls of the high-TDP GPU era.

Sources: Reddit, via VideoCardz
Add your own comment

105 Comments on Unofficial 12V-2x6V Power Connector Melts NVIDIA GeForce RTX 5090

#101
chrcoluk
CrackongDer8auer got the card & cable & PSU.
Observed and compared the results with his own 5090.
Finds out there are 2 wires carrying 20A in stress testing. (Other wires carried ~5A)
It makes those 2 wires extremely hot and dangerous.




Skip to 13:06 for the important stuff, video is padded out a lot.
Posted on Reply
#102
user556
ninjafadayeah they need to improve the aera of connection too and those cylindric system are always a pain in the a***
perhaps one day we are gonna have plug with screw to tighten plugs
The 12V-2x6 plug works already. The only problem is there is a lot of the 12VHPWR cables still out there. Even Der8auer stated all his test setup is 12VHPWR. Those should all be recalled.
Posted on Reply
#103
jnv11
user556The 12V-2x6 plug works already. The only problem is there is a lot of the 12VHPWR cables still out there. Even Der8auer stated all his test setup is 12VHPWR. Those should all be recalled.
There is no difference between the 12V-2x6 and 12VHPWR standards when it comes to cables according to www.corsair.com/us/en/explorer/diy-builder/power-supply-units/will-my-12vhpwr-cable-work-with-12v-2x6/ . If there are any differences between a manufacturer's 12V-2x6 and 12VHPWR cables other than labeling, names, and part numbers, then either the manufacturer is possibly admitting that its 12VHPWR cables are garbage because it cut down the quality of the 12VHPWR cables to be just good enough for an RTX 4090 and is not good enough for an RTX 5090 because the RTX 5090 draws more amps and therefore demands more of the cable than what an RTX 4090 demands.
Posted on Reply
#105
Crackong
Burnt 5080 appeared on Reddit
- Rog card showed warning
- User checked and found out one pin on the PSU side melted
- GPU stuck at PCIE x3 mode
- GN Steve reached out and hopefully buying the setup for analysis.

ASUS/comments/1inhbo7
Posted on Reply
Add your own comment
Nov 22nd, 2026 01:16 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts