Sunday, September 7th 2025
Samsung's GDDR6 Modules Run 10°C Cooler Than SK Hynix, Claims GPU AIB
XFX has officially published various performance figures claiming that its custom GPUs run better with Samsung GDDR6 memory, rather than SK Hynix modules. Usually, add-in-board (AIB) partners receive the GPU die sold as a kit with memory. However, AMD, NVIDIA, and Intel typically source their memory modules from various partners, including Samsung, SK Hynix, and Micron. GPU AIBs can sometimes prioritize a single memory maker, and this time it looks like Samsung GDDR6 memory modules are turning out to be a much better design for the XFX GPUs. "In terms of hardware, memory power consumption and heat dissipation also directly impact overall stability. Previously, the XFX 9060 XT used Hynix memory, but this time, the XFX 9060XT V3 has switched to Samsung memory. Not only is the GPU cooler, but its DDR temperature is 10°C lower than the Hynix version" says XFX on BiliBili.
The performance comparisons show that Samsung's GDDR6 memory runs at 77°C, while the SK Hynix modules run at 10°C hotter, 87°C. Switching to Samsung-made modules also brings down the total board consumption to 183 W, down from 207 W with SK Hynix. This is 24 W of heat, which the cooler system picks up, resulting in a lower fan speed. In contrast, the Samsung version spun the fans at 1461 RPM, while the SK Hynix version spun at 1814 RPM. This means that the overall GPU system is being more stable, generally more effective, prevents VRAM downclocks, and has higher stability. Interestingly, the choice of Samsung memory increases the GPU die temperature by 3°C, indicating that the memory controller on the die is likely operating at a higher intensity, or the lower fan speed resulted in less cooling. While we await more details and independent testing, it is interesting to see just how much a memory vendor choice can impact the overall GPU performance. There is little information on XFX 9060 XT V3 design, but it is already available in China.
Sources:
BiliBili, via VideoCardz
The performance comparisons show that Samsung's GDDR6 memory runs at 77°C, while the SK Hynix modules run at 10°C hotter, 87°C. Switching to Samsung-made modules also brings down the total board consumption to 183 W, down from 207 W with SK Hynix. This is 24 W of heat, which the cooler system picks up, resulting in a lower fan speed. In contrast, the Samsung version spun the fans at 1461 RPM, while the SK Hynix version spun at 1814 RPM. This means that the overall GPU system is being more stable, generally more effective, prevents VRAM downclocks, and has higher stability. Interestingly, the choice of Samsung memory increases the GPU die temperature by 3°C, indicating that the memory controller on the die is likely operating at a higher intensity, or the lower fan speed resulted in less cooling. While we await more details and independent testing, it is interesting to see just how much a memory vendor choice can impact the overall GPU performance. There is little information on XFX 9060 XT V3 design, but it is already available in China.


24 Comments on Samsung's GDDR6 Modules Run 10°C Cooler Than SK Hynix, Claims GPU AIB
Ironically you can't even tell if the Samsung Chips where clocked slower than the SK Hynix ones as the speed is not mentioned anywhere as far as I can see...
Just a little trade off to have slightly better performance.
With thermal pads it obviously won't work and is not supposed to work, because these trap / block the heat transfer - don't promote it.
www.techpowerup.com/review/xfx-radeon-rx-9060-xt-swift-oc-16-gb/
His memory temps are in general 8-10°C hotter.
I'm able to clock my memory to 2800 MHz without losing performance, his maxes out at 2730 MHz. Both running at fast timings.
videocardz.com/newz/amd-radeon-rx-9070-xt-with-samsung-memory-shows-slight-benchmark-drop-in-22-card-comparison
182-24=158. So much for Blackwell's supposed efficiency advantage.
I prefer performance over up to 105°C acceptable temperature range.
A paid review because SAMSUNG does not deliver any decent products? Plausible.
I've had experience with 5 different 9070 XTs, 3 of them are Samsung and 2 of them are Hynix. Both of the Hynix cards run hotter on the memory.
There were some rumors that the Samsung memory is using a bit looser timings, but it can also OC a bit further. I was able to OC mine all the way to 2800 MHz on fast timings. A friends Hynix card can only do 2730.
I tested it and beyond 2850 it starts to lose performance. Im not that concerned about the 90c memory temps. Im more concerned about the occasional 105c GPU hot spot.
Alphacool cant release their Eiswolf GPU AIO for 9070 XT soon enough...
Yes they have full cover water blocks for various AIB models, but i dont want to build a custom loop.
The reduced temperature and power is definitely nice if holds up under scrutiny in terms of the details around it.
We miss the core point: What is faster.
I'm well aware of that my 7800xt card treat me like an idiot with loose and tight timings. The better Gpu RAM is the faster one in benchmark or the same demanding game with the same graphic chip.
Some other german language forum claim the hynix is faster. Because more Megaherz. I think they do not use MT/s for gpu dram. I think pcgh users were discussing about the same context and news article in german.
I'm just interested :)
No idea: Is something like steel nomad to test for that?
I know that 3DMark is a paid program so maybe someone can chip in what would be a good memory test? Maybe some in-game benchmark. If we have to, we will use our big boat and roam the seas for it :roll:
Edit: 3 of us are rocking 9800X3Ds with so it will be a very apples-to-apples comaprison. I'm the only one with 64 gigs of RAM.