X800 fuses data for unlocking

[VulkanBros]

MSI X800se

What about this one....is it looked ?

$ffffffffff Display adapter information
$ffffffffff ---------------------------------------------------
$0000000000 Description : RADEON X800 Series
$0000000001 Vendor ID : 1002 (ATI)
$0000000002 Device ID : 4a4a
$0000000003 Location : bus 2, device 0, function 0
$0000000004 Bus type : AGP revision 3.0
$0000000005 AGP status : enabled
$0000000006 AGP rate : 4x 8x supported, 8x selected
$0000000007 AGP SBA : hardwired, enabled
$0000000008 AGP FW : supported, enabled
$0000000009 Base address 0 : d0000000 (memory range)
$000000000a Base address 1 : 0000c000 (I/O range)
$000000000b Base address 2 : e1000000 (memory range)
$000000000c Base address 3 : none
$000000000d Base address 4 : none
$000000000e Base address 5 : none
$ffffffffff ---------------------------------------------------
$ffffffffff ATI specific display adapter information
$ffffffffff ---------------------------------------------------
$0900000000 Graphics core : R420 (8x1)
$0900000002 Memory bus : 256-bit
$0900000001 Memory type : DDR3 SGRAM
$0900000003 Memory amount : 256MB
$0900000004 Core clock : 425.250MHz
$0900000005 Memory clock : 398.250MHz (796.500MHz effective)
$0900000006 Reference clock : 27.000MHz

 

[neologan]

Connect3D X800 GTO, looking at the core it doesn't say R480, it just says X800.

Is this moddable?

 

[dolf]

Your results are interesting and I supose that you have R423 with laer-cut from the right. Left has to be still connected. One quad should be disabled but it is not like on the other cards. If you want it is better to remove the cooler and to inspect what is under.
If I am right you should connect the right cut and to conduct again the fuse research. Probably you can have 16 pipes but who knows?

You also can preliminary flash with 16 pipe BIOS and to see whether 16 pipes will work but I am not very convinced that it will happend unless you don't hardmod it .

Good luck.

 

[Thermopylae_480]

MSI RX800 R430 GPU

CONGFIG_DIE_FUSES 0xFFFFBFFF
CONFIG SUBSTRATE FUSES 0xFFFFFF9E
CONFIG_ROM_FUSES 0xA61
GB_PIPE_SELECT 0x12B84

 

[Steevo]

X800GTO AGP
Sapphire

I haven't maxed out the memory yet, but.

Core 454
Mem 540


Scored 4915 3Dmark05

Intel Prescott 2.8 OC'ed to 3.0 533 MHZ FSB
1Gb Corsair Value RAM @ 333
Intel 865 PERL mobo
2) 120GB Maxtor DM9 in RAID 0
X800GTO Sapphire AGP
Onboard sound



I am selling my compy to the company in the next couple months, will be upgrading to a AMD64 and X1800XT 2GB RAM system. Just bought this card for some extra HW support in the next two months.

Anyway, any ideas on unlockability? I have flashed a 9800PRO (after many tried BIOS's and re-writing one of my own), changed the cooler, and OC'd the piss out of my 9600XT.

 

[Steevo]

OK, tomorrow I will pull the card, remove the cooler and check the core for number, and laser cuts. But it appears that these later X800GTO's AGP CAN be modded.

At least that is what I am reading, from the hex. 1 quad is disabled and the core is seen as a R430 by BIOS configuration.

A better cooler is needed for higher clock speeds. Sapphire uses higher quality memory so you are good there. I have taken my memory speed up to 600Mhz and it performs fine.

 

[Sibic]

The Sapphire X800GTO's can be clocked extremely high. I have mine running 400 @ 607 on the core and 490 @ 621 on the memory, and it's stable. I would highly recomend getting something other than the stock cooler if you plan running it that high, because mine got close to 90 degrees with speeds that were much much lower than thoose, and even thoo it can run on 90 degrees it's certainly not healthy. I have a Zalman 700 copper on mine, and it's about 65 degrees after a few hours of gaming, with 100% on the fanspeed.

 

[Steevo]

I have gotten errors at 460 core but it is running very warm. I don't want to change the cooler as this is a temp fix untill I get a new system. And I will be selling the card to a friend and putting the 9600XT back in when I sell this system.

I also have RAMsinks to apply yet and will be changing the TIM to AC5 and redirecting the air flow. RIght now my front 120mm pushes a mixture of warm air from the card and cool incoming air back into the card. I am going to add a chute to move it out a empty slot in the back.

I will have to move my disassembly back to Sat, as the lady of the house demands my time tonight. I expect that there will be some indecent and lewd activity, so the compy loses.

 

[carlo_mpg]

Here`s my Powercolor X800GTO 256 GDDR3 VIVO PCIE can it be moddified??

haven`t verified the core.

thx!

http://img138.imageshack.us/img138/5340/x800gtoatitool8hc.jpg

 

[Steevo]

OK, after removing my coolers and whatnot.


ATI R430 core
Infineon Memory
No laser cuts anywhere.

And according to the BIOS I have a quad locked in there.


It is a Sapphire X800GTO AGP DDR3
With a output of
CONFIG_DIE_FUSES 0xFFFFBFFF
CONFIG_SUBSTRATE_FUSES 0xFFFFFF9E
CONFIG_ROM_FUSES 0xA61
GB_PIPE_SELECT 0x12B84

Using 5.10 ATI drivers I have achieved an OC of

Core 465
Mem 560

Stable. Any more on the core and I get a lockup. 4951 scored on 3Dmark05.

And here is the BIOS

 

[decline]

this is one of those c3d x800 gto unlockable

 

[Steevo]

Anyone want to mod my BIOS so I can get my last 4 pipes and mebey a little more OC'ing room?


If I ask really nice?

 

[ShadowFlare]

Anyone want to mod my BIOS so I can get my last 4 pipes and mebey a little more OC'ing room?


If I ask really nice?

Here is a 16 pipeline modded bios, but that's all I can do for you. I don't know of any way to mod the bios to help with overclocking.

 

[Steevo]

Thanks.

 

[Sapphire]

Here is my cards info from under the cooler

gpu:
215rbmaga12f
gc9007.1
0438ss

Memory:
Samsunhg 531
k4j55323qf-gc20
awe385gaa

is this card unlockable???
and what core do i have? is it a 438???

cheers

 

[Steevo]

Still 12 pipes. Still is only identifying as a X800

I am going to compare a BIOS from a AGP X800XT to this one and see what I get in difference. I know the memory is different. But the rest might be what is holding it back.


4970 3Dmark05 now


The AC5 made a difference, now I can get the core up to 470.

 

[ShadowFlare]

Still 12 pipes. Still is only identifying as a X800

I am going to compare a BIOS from a AGP X800XT to this one and see what I get in difference. I know the memory is different. But the rest might be what is holding it back.


4970 3Dmark05 now


The AC5 made a difference, now I can get the core up to 470.

If you flashed that bios right, then your gpu isn't unlockable with just a bios flash. Are you talking about find differences in bioses to figure out how to unlock it or just how to improve overclocking by using another bios?

 

[Sapphire]

Here is my cards info from under the cooler

gpu:
215rbmaga12f
gc9007.1
0438ss

Memory:
Samsunhg 531
k4j55323qf-gc20
awe385gaa

is this card unlockable???
and what core do i have? is it a 438???

cheers

can anyone help me please?

 

[Megatron]

It looks hard locked from those figures.

 

[leodaso]

ATI X850 Pro VIVO AGP with laser lock on core bridged and X850 Pro VIVO 16 pipe modded bios.

ATI Tool still shows 12 pipes in use. What else can I try? Or am I just wasting my time?

 

[ShadowFlare]

ATI X850 Pro VIVO AGP with laser lock on core bridged and X850 Pro VIVO 16 pipe modded bios.

ATI Tool still shows 12 pipes in use. What else can I try? Or am I just wasting my time?

There is nothing else you can do without doing some modding of the actual hardware. A last digit of zero in CONFIG_ROM_FUSES means that no pipeline quads are locked in the bios. Since you have a zero there, it means that you did get the 16 pipeline bios flashed correctly.

 

[pao-lini]

Hi,

I have just buyed a X800 GTO and with Ati Tool i see that i have 12 pipe and lasercut, i try to flash bios with X800gto2 modified and flash run Ok, i have 0x260 but always 12 pipe, in this case the 4 pipe are lasercut, i can i hardmod and re-attach the pipe ?, may someone help me ? please send in forum photos with indicated the lasercut to re-attach and i try !!!
Thank you very much
Paolo

 

[h2o]

help!

Hello!
i have SVGA 256Mb <PCI-E> DDR Sapphire Ultimate Edition <ATI RADEON X800 GTO> (OEM) 256bit +DVI+TV Out GDDR3
It has 12 active pipelines and samsung 2.0 memory and R480 chip
standart 390 GPU/490 memory
i tryed to overclock it and i have on stable 580 GPU and 545 Memory. Memory - on max. after 545 - artifacts going on display. But GPU works with 600 and more, but it works short time and then display going dark, then black, and then my PC is hang up. Temperature was about 40-50 C. Is it because i have 12 active pipelines instead 16?

So, can i make 16 active pipelines?

ATITool 25 beta 8 shoes me
CONFIG_DIE_FUSES 0xFFFF E FFF
CONFIG_SUBSTRATE_FUSES 0xFFFFFFF E
and next 2 strings also enother then in http://www.techpowerup.com/articles/overclocking/vidcard/127

When i plug my card into PC and starts XP, it said "Radeon X850 series".

Please help to unlock my card!!!
Thx forward... sory for bad english... russia forever!

 

[dolf]

Sorry but with these fuse results you will not have 16 pipes .

 

[carlo_mpg]

what about my card? nobody has given me any answer...posted config and nothing...

i don+t have the F`s in the strings...does this mean I can`t? thankx

here is the picture..