Tuesday, February 24th 2026

Multiple Reports Emerge of MSI 12v-2×6 PSU Connectors Creeping Out of GPUs

One of the simpler solutions manufacturers have come up with to mitigate the ubiquitous 12v-2×6 GPU power connector meltdowns is colored cable terminations that simply give the user an indication that the GPU power connector is properly connected. According to a recent post on r/MSI_Gaming, those colored connectors are both doing their jobs and causing concerns among MSI PSU users. The original poster shared an image of the stock 12v-2×6 power cables of an MSI MPG A1000GS ATX 3.1 PSU that had slowly been creeping out of both the PSU and PNY RTX 5080 GPU connectors over the course of two months, exposing the colored yellow connector end that is meant to serve as a warning against thermal meltdown events.

While the slowly loosening connector had not yet resulted in a meltdown, it had seemingly started causing instability in the user's system during heavy gaming loads. What's more concerning is the multitude of comments in the Reddit thread echoing the OP's story, saying that they had properly connected both ends of the cable until there was a positive click, but despite this, the cable seemed to be creeping out at one or both ends. Some commenters hypothesized that part of the reason for these meltdown events that happen so long after the system was first built is that repeated thermal cycling causes the plastic connector to expand and contract, resulting in the cable slowly coming loose. The redditor was eventually told to request a replacement unit through Amazon, but if the number of similar reports in the same thread are anything to go by, the issue appears to be at least somewhat widespread with MSI's cables.
Source: u/SnooPaintings7769 on Reddit
Add your own comment

20 Comments on Multiple Reports Emerge of MSI 12v-2×6 PSU Connectors Creeping Out of GPUs

#2
evernessince
There was another few reports of this kind of failure half a year ago. Not sure if it's just the MSI connector or the latch design in general. Dell's version of the connector seems to take extra lengths to ensure they don't come loose so I suspect it may be a bit of MSI cheeping out and the spec (although that's exactly why having a wider safety margin ins helpful).
Posted on Reply
#3
Bwaze
As far as I understood the connectors only creeped out a bit - the latch was still engaged, but it has a bit of a play between fully seated cable and it - how can this barely perceptible fraction of a millimetre shorter seating cause bad connection, with stability problems in games?
Posted on Reply
#4
Space Lynx
Astronaut
i have corsair psu, got a flashlight out now just to double check cause of this article, lmao

all good on my end
Posted on Reply
#5
Wirko
I have finally thought up a good solution to all problems. The yellow plastic should have a very stinky additive that is activated and released at a certain temperature, a little before it begins to smoulder or burn!
Posted on Reply
#6
N/A
No smell or smoke detector required. Simply short the sense pins at >60C, 100W and disconnect ground after 80C, 0W
Posted on Reply
#7
Bwaze
The problem is, when various reviewers checked the temperatures of their cables, they got some very high numbers even with good and fully seated cables, just with the contact variance causing more power through cables with better connection. In theory cable gauges and connectors should be more than capable of handling RTX 5090, overclocked, at full power, but in the real world the connector is so badly designed it performs on the edge of meltdown even when everything is "OK, not perfect", and problems can arise with cards that draw much less power.
Posted on Reply
#9
Mysteoa
BwazeAs far as I understood the connectors only creeped out a bit - the latch was still engaged, but it has a bit of a play between fully seated cable and it - how can this barely perceptible fraction of a millimetre shorter seating cause bad connection, with stability problems in games?
We can't be sure how good the connection was when the cable was fully sited. So it could be, after it moved, it made the connection much worse and made for bad power delivery.
Posted on Reply
#10
rattlehead99
Repeat after me: 200W GPUs with 1x 8 pin cable or at most 250W GPUs with 1x 6 pin and 1x 8 pin, there were engineering standards for a reason for such a long time.
Posted on Reply
#11
N/A
6-pin PCIe 75W, 8-pin 150W, same as 6-pin with 2 signal ground pins that do nothing. So free upgrade.
rattlehead99Repeat after me: 200W GPUs with 1x 8 pin cable or at most 250W GPUs with 1x 6 pin and 1x 8 pin, there were engineering standards for a reason for such a long time.
12-pin is a glorified 2x 6-pin PCIe, so 150 or 300 W.

If it slips out, it means the lock is completely non-existent or has been eaten, but they leave out the most important piece of the information, which leaves us frustrated.
Posted on Reply
#12
forman313
WirkoI have finally thought up a good solution to all problems. The yellow plastic should have a very stinky additive that is activated and released at a certain temperature, a little before it begins to smoulder or burn!
Something like Phosphine or Thioacetone you mean?

In the future, maybe Furmark will be called Furbarf....
Posted on Reply
#13
Tomorrow
Another day. Another 16pin problem. Usually i would say kill it with fire, but considering the end result there's no need, is there?
Posted on Reply
#14
Unregistered
I have a 4070ti with this connector and mine does not connect firmly. Even after hearing the the connector click it will pull out easily.
#15
Gucky
Bwazehow can this barely perceptible fraction of a millimetre shorter seating cause bad connection, with stability problems in games?
It doesn't by itself.
Look at the third picture. It has a bend downwards, so the whole connector is being forced into one direction. That onesided force can cause pins to lose some contact.
And yes that clip has been a problem since day one. You can minimize the tolerances, but you can't fix it without making a whole new connector, killing compability to all current GPUs and PSUs. That's why it is a shitshow with companies using the broken connector and not really fixing it.
N/ASimply short the sense pins at >60C,
Then no 5090 would work. Fans usually turn on at around 60°C, but in idle the whole cooler and PCB get saturated. For example my 4090FE had its cooler reach 60°C all around before fans turned on.
Posted on Reply
#16
TheDeeGee
Thermal cycle and micro vibrations from current do this.

This power connector simply sucks from all sides.

Back to reliable 6/8-Pin.
Posted on Reply
#17
EsaT
BwazeAs far as I understood the connectors only creeped out a bit - the latch was still engaged, but it has a bit of a play between fully seated cable and it - how can this barely perceptible fraction of a millimetre shorter seating cause bad connection, with stability problems in games?
Normally it wouldn't be significant because of safety margins.
But this abomination connector doesn't have any safety margins.
Hence any imperfections are risk of voltage and power loss becoming something other than insignificant.
N/A12-pin is a glorified 2x 6-pin PCIe, so 150 or 300 W.
Except that pins are smaller and more densely packed and hence real current capability per pin is lower.
Posted on Reply
#18
_roman_
how much are screws?

cars have so many connectors with latching mechanism

did any vga connector went loose when the screw was bolted to maximum?


intel and nvidia should learn about screws and retention force.

when you pull on a cable you should never unlatch it. that is a common test in QA during production for injection molding parts when the customer had a requirement for it. zwick sells such machines. u have to make a test jig yourself.
Posted on Reply
#19
Quicks
Yeah right user errors they said, cable safe they said... blame the user.

Time someone takes Nvidia and everyone else to the cleaners for piss poor cable design.
Posted on Reply
#20
Scrizz
meanwhile I still have my 4090 since launch with no problem. 🤷‍♂️
Posted on Reply
Add your own comment
Nov 20th, 2026 20:04 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts