Wednesday, September 2nd 2026
Early DLSS 5 Testing Suggests the RTX 5090's Single Power Connector Might Be the Bottleneck
Community testing of leaked DLSS 5 builds suggests the tech may already be hitting a wall on NVIDIA's own flagship GPU. Tom's Hardware ran the neural rendering model through Cyberpunk 2077, Hogwarts Legacy, and Control on an RTX 5090 Founders Edition, as well as an MSI RTX 5090 Lightning Z. Surprisingly, the results point to power delivery as the potential bottleneck rather than compute horsepower. The test used a community Optiscaler injection method built on the leaked DLSS 5 DLL, not NVIDIA's official Streamline path, though the cost lined up closely with NVIDIA's own published 8 ms-per-frame figure.
The Founders Edition, limited to a single 12V-2x6 connector, dropped framerates by 42 to 49 percent with DLSS 5 enabled and consistently hit its 575 W power limit while doing so. The MSI Lightning Z, with a dual-connector setup and a 1000 W limit, took a smaller hit and held better 1% lows, while pulling far more power. In Hogwarts Legacy, it jumped from 480 W to 720 W with neural rendering active, which is a sizeable 50% increase. That leaves single-connector RTX 5090 cards apparently underprovisioned for a feature this demanding, at least unofficially.The Founders Edition wasn't short on compute so much as it was limited by its own power ceiling. This is notable given how much scrutiny the 12V-2x6 connector has already drawn this generation. DLSS 5 officially launches September 3 with NBA 2K27, and it should become clear within days whether NVIDIA's first-party version fares any better on the Founder's Edition RTX 5090. If not, we might have to wait for future Super variants or next-gen cards to truly maximize the potential of DLSS 5.
Source:
Tom's Hardware
The Founders Edition, limited to a single 12V-2x6 connector, dropped framerates by 42 to 49 percent with DLSS 5 enabled and consistently hit its 575 W power limit while doing so. The MSI Lightning Z, with a dual-connector setup and a 1000 W limit, took a smaller hit and held better 1% lows, while pulling far more power. In Hogwarts Legacy, it jumped from 480 W to 720 W with neural rendering active, which is a sizeable 50% increase. That leaves single-connector RTX 5090 cards apparently underprovisioned for a feature this demanding, at least unofficially.The Founders Edition wasn't short on compute so much as it was limited by its own power ceiling. This is notable given how much scrutiny the 12V-2x6 connector has already drawn this generation. DLSS 5 officially launches September 3 with NBA 2K27, and it should become clear within days whether NVIDIA's first-party version fares any better on the Founder's Edition RTX 5090. If not, we might have to wait for future Super variants or next-gen cards to truly maximize the potential of DLSS 5.




52 Comments on Early DLSS 5 Testing Suggests the RTX 5090's Single Power Connector Might Be the Bottleneck
I wonder though, if you remove the tensor cores and rt cores and divert that space to rastererization, what would the results be? (at the same power)
I sure hope they can get it running somehow on nvINT4, and that this gives enough performance overhead to keep power draw in check...
I can lower it back down with heavy FG implementation, but it feels like I am trying to pull myself out a mud pool, horrible input latency.
And in benchmarks like 3DMark it takes 500W, there is still 15% left.
All while being a bit faster then stock.
Good job AI company at failing to write software to test all aspects of their card at the same time.
Also, Furmak2 can do a decent job at emulating this... however it's a "power virus" and "unrealistic" LOL
Sucks to be the guy to tell RTX 60 cooling group that "TDP... has to go up again" :laugh:
Seriously, they should just give up and use 0.8V as maximum voltage for GPU cores (normal operation 0.6-0.7).
Cyberpunk
Z 99->60 = 40% drop
FE 88->51 = 42% drop
Control
Z 107->61.6 = 42%
FE 87.5->50.9 = 42%
- DLSS5 on, FE versus the Z - we see a 10% improvement in FPS for a 40% increase in power draw.
I am failing to see the context of why this is even an article.
And since these connectors are attached to the PCB, you need another 5090!
That you will also need to run DLSS5 with decent FPS.
So you will have 1300 watts of GPU-Power alone, to run AI-Slop on your Games.
This is gonna be the next big hit in Gaming, trust me!
Actually, scratch that, 75watt is the limit of the slot. We can't push connectors to their limit. We need to reduce that. No gaming GPUs over 30 watt.
Nah, let's just ban consumer GPUs. Integrated GPU or bust. Soldered CPUs and memory only. Then there is no melting risk!
Hardware Unboxed had their 5090 melt, this connector should have never been standardized, or forced upon the entire industry.
/s of course.