Saturday, October 3rd 2026

Modder Solders Dual 8-Pin Board to RTX 5090's 16-Pin Header, Wires Stay Below 40°C

Melting 16-pin connectors keep making headlines, and some RTX 5090 owners have started taking the protection of their expensive cards into their own hands. Reddit user DallasGrave has modified an MSI GeForce RTX 5090 with two extra 8-pin PCIe power inputs that work alongside the card's original 16-pin connector. According to their post on r/pcmasterrace, a small pickup PCB is soldered to the contacts of the 16-pin header, and that board feeds a second PCB carrying the two 8-pin sockets. The card then runs on three cables in total. DallasGrave says each conductor now carries roughly 3 A, and that the wires never crossed 40°C during a 48-hour run at 550 W, even at the joint. More test data is apparently on the way, so for now these are the modder's own numbers.

The 12V-2x6 revision was supposed to fix the melting power connector issues. In early 2025, NVIDIA said the 16-pin melting issues were over, pointing to the updated connector on the RTX 50-series. However, the first melted RTX 5090 Founders Edition was reported shortly after, in that case with a third-party cable. Since then, several RTX 5090 power connectors have reportedly melted, including one with an undervolt and a -100 W power limit. Moreover, last month Hardware Unboxed watched its RTX 5090 power cable reach 175°C with a single wire pulling around 22 A.
Modders have had to jump in with fixes of their own, since off-the-shelf solutions have had a mixed record so far. ASUS introduced the ROG Equalizer cable to spread current more evenly, yet a photo of a burned one later surfaced online. ASRock's TempGuard also reportedly failed to stop a PSU-side meltdown on an RTX PRO 6000 rig. This new mod is clever, though soldering onto a card this expensive is probably best left to experienced hands. It's also a milder approach than what Brazilian channel TecLab did recently, first soldering power wires straight to the PCB and later running an RTX 5090 on three 8-pin connectors. Here, the 16-pin connector stays in use and simply carries less of the load.
Source: Reddit
Add your own comment

86 Comments on Modder Solders Dual 8-Pin Board to RTX 5090's 16-Pin Header, Wires Stay Below 40°C

#26
freeagent
lexluthermiester?!? What's a "torrent"?
My case lol..
Posted on Reply
#27
user556
lexluthermiesterThere's likely some of that happening, but the wires themselves are heating up as well.
No they aren't. Or at least nothing that matters. All the real heating is in the pins. Actually, the hot pins aren't the problem either. It's the cold pins that have failed to do their job. Putting all the burden on the remaining pins.
lexluthermiesterSorry, no. The connector is part of the problem, yes. It's not all of the problem.
The cable plug (female pins) is the only problem. Nothing else at all.
Posted on Reply
#28
withanewforce
that 12VHPWR looks so wimpy. 3080 FT3 has 3 8 pin connectors looks really nice. they should have designed a big ass plug like the 24pin MB plug. would look really nice connected in then the splitter used on many 12VHPWR
Posted on Reply
#29
kazuviking
withanewforcethey should have designed a big ass blug like the 24pin MB plug
What asus is using for btf shouldve been the original 12hpwr connector. It have 4 T H I C C copper connects which is rated 30A continuous with nice headroom, 50A for fuck it we ball and 100A max.
Posted on Reply
#30
JustBenching
lexluthermiester?!? What's a "torrent"?
Fractal torrent, a pc case I assume. Topped the airflow charts. I have one, pretty good but not aio friendly, it's for air coolers.
Posted on Reply
#31
TheDeeGee
Since 8-pin is rated for 341W a 5090 could be safely powered by just 3 of them.
Posted on Reply
#32
A Computer Guy
user556The cable plug (female pins) is the only problem. Nothing else at all.
Or you can blame the male pins for not being girthy enough.
Posted on Reply
#34
Chaitanya
Slesreth

Interesting.
So PNY gets to point finger at someone else for the modifications and get away with breaking "official" design guidelines.
Posted on Reply
#35
melkor_unlimited
CrackongSo there are 12 wires carrying all the load...
More than 3x8pin already
ofc it is fine

Looks like it is not so obvious.

In 8-pin connector there are 3 wires delivering 12V.
In 16-pin (read as 12+4 pins) there are 6 wires delivering 12V.

Elementary school 2nd grade math question: "How many 8-pins you need to get 6 wires providing 12V?"
A Computer GuyThat's an optimistic point of view. I would have gone for a planned obsolescence theory in order to drive more sales.


I feel like it's only time before Thermal Grizzly catches on to this and is like - I can design and solder PCB connectors too! Then we start seeing some modded GPU's for sale with TG backed warranty like those delidded CPU's they sell.
As if any warranty could you any good in those times.
- Serial # faded away -> warranty void
- used cables delivered with PSU -> warranty void

If there is nothing else --> user error --> warranty void
Posted on Reply
#36
ymdhis
A Computer GuyNvidia is not Nintendo. I'd wager right to repair would ask Nvidia to hold its' beer.
Is that why they build their $1000+ cards with a thin cable that is known to always overheat and break? Remember even if you RMA it (which stores not always honor), that costs the store another card, and nVidia another sale. This is planned obsolescence built in.
Posted on Reply
#37
melkor_unlimited
freeagentMy case lol..
Torrent as Fractal Design - Torrent?

ymdhisIs that why they build their $1000+ cards with a thin cable that is known to always overheat and break? Remember even if you RMA it (which stores not always honor), that costs the store another card, and nVidia another sale. This is planned obsolescence built in.
Even if they accept the RMA, they probably will return you only the paltry sum of $1800 and let you find the rest to buy new GPU for $5000+
Posted on Reply
#38
Crackong
melkor_unlimitedElementary school 2nd grade math question: "How many 8-pins you need to get 6 wires providing 12V?"
The OP post stated it is a 16pin + 2 x 8pins.
3 cables working together.
Total of 12 pins delivering 12V
Posted on Reply
#39
bad1080
Athenaone small mistake, and it can go up in smoke
they regularly go up in smoke without modifications too, so 🤷‍♂️
Posted on Reply
#40
melkor_unlimited
CrackongThe OP post stated it is a 16pin + 2 x 8pins.
3 cables working together.
Total of 12 pins delivering 12V
The more (wires) the merrier 😃

Missed this one ...
two extra 8-pin PCIe power inputs that work alongside the card's original 16-pin connector
I am going old.
Have to be more careful when speed reading.
Posted on Reply
#41
RejZoR
lexluthermiesterLet's be honest, the engineers very likely do, but the nitwit execs over-rule them. Corporate reckless incompetence shining like a polished turd for all to see.
Thicker wires would fare way better, but execs only look at this through lens of "but we'll spend X number of cents more per wire for every graphic card so that's a big no no". Even if they doubled the cost and put it on the user it wouldn't fucking matter. Like, what is paying 20€ more for a graphic card that already costs over 1000€ (talking about shit like RTX 5070Ti) and becomes even less relevant with RTX 5090. This is why I always get mad over such dumb designs because savings must be done. For what?!?!?!? To make a more shit product?

I've had Sapphire Radeon with 12VHP connector ordered but they ran out and I got the XFX Mercury OC instead with 3x 8pin. I'm actually glad it went this way. Whole 12VHP is just such absolute stupidity from ground up I want to just entirely skip this entire nonsense. Even that 2x6 new thing, I'm gonna just skip it all because it's a dumb standard that should die already.
Posted on Reply
#42
NutZInTheHead
lol. the things people come up with to fix such simple yet crucial problems that a trillion dollar company wont fix themselves. Shame on me that I spent so much $$$ all those years buying their junk.
It's true my EVGA 1080 Ti is or rather was the best card I ever owned, but now that I am on AMD side (first AMD card btw), i can honestly never go back.
Posted on Reply
#43
Grimling
WirkoA cease and desist letter. If AIBs are not allowed to use solutions like current sensing on each wire or 8-pin connectors, why would some random genius with a soldering iron be free to invent something better and share this forbidden knowledge with the general public?
LOL, AIBs have agreed in a Contract with Nvidia, to obey Nvidias 12v-2x6 Connector rules.
This Modder has not, it is his Card, he owns it, and he can do with it whatever he wants!
Posted on Reply
#44
RedelZaVedno
This 12v-2x6 Connector thing must be intentional. I've been designing power grids my whole life and I would never use CU/AL cables instead of ACSR/AAAC/ACSS ones on high voltage power distribution grids but mutatis mutandis Nvidia is doing just that. Pure insanity.
Posted on Reply
#45
xxxZAURxxx
1- I'll buy Nvidia's current card once the 8-pin design returns.
2- I'll use Windows once the Copilot AI is completely removed.
3- I'll build a new system when RAM prices drop.

If these things don't happen, I'll build a DDR2 system in the future and stick with the Linux operating system.
We don't dig a hole and find the money; we earn it through hard work.
Posted on Reply
#46
notoperable
I smell Nvidia new businesses venture, 5090 retro edition - Power delivery that isn't butter
Posted on Reply
#47
SirB
WirkoA cease and desist letter. If AIBs are not allowed to use solutions like current sensing on each wire or 8-pin connectors, why would some random genius with a soldering iron be free to invent something better and share this forbidden knowledge with the general public?
Ya, but this guy isn't selling the cards.
Posted on Reply
#48
notoperable
_Zaur_1- I'll buy Nvidia's current card once the 8-pin design returns.
2- I'll use Windows once the Copilot AI is completely removed.
3- I'll build a new system when RAM prices drop.

If these things don't happen, I'll build a DDR2 system in the future and stick with the Linux operating system.
We don't dig a hole and find the money; we earn it through hard work.
hell freezes over and universe arrives at thermal death stage first before this happens, prepare for a long wait
Posted on Reply
#49
JustBenching
RejZoRThicker wires would fare way better, but execs only look at this through lens of "but we'll spend X number of cents more per wire for every graphic card so that's a big no no". Even if they doubled the cost and put it on the user it wouldn't fucking matter. Like, what is paying 20€ more for a graphic card that already costs over 1000€ (talking about shit like RTX 5070Ti) and becomes even less relevant with RTX 5090. This is why I always get mad over such dumb designs because savings must be done. For what?!?!?!? To make a more shit product?

I've had Sapphire Radeon with 12VHP connector ordered but they ran out and I got the XFX Mercury OC instead with 3x 8pin. I'm actually glad it went this way. Whole 12VHP is just such absolute stupidity from ground up I want to just entirely skip this entire nonsense. Even that 2x6 new thing, I'm gonna just skip it all because it's a dumb standard that should die already.
Assuming there is an issue with 12vh. You add 20$ to around 150m GPU Nvidia sells every Gen, that's 3b$. All that money to fix an issue that affects only their higher end models. If their higher end models are 10% or the sales you are looking at a problem that basically affects 0,1% of their gpus. It's much cheaper to replace all these cards than increase the cost of production by 20$
Posted on Reply
#50
wEeViLz
I don't understand why there isn't a mandatory recall, if this problem were in a car the makers would be forced to come up with a safe fix, this is a dangerous situation yet no consumer protection at all?
Posted on Reply
Add your own comment
Nov 20th, 2026 04:57 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts