Saturday, October 3rd 2026

Modder Solders Dual 8-Pin Board to RTX 5090's 16-Pin Header, Wires Stay Below 40°C

Melting 16-pin connectors keep making headlines, and some RTX 5090 owners have started taking the protection of their expensive cards into their own hands. Reddit user DallasGrave has modified an MSI GeForce RTX 5090 with two extra 8-pin PCIe power inputs that work alongside the card's original 16-pin connector. According to their post on r/pcmasterrace, a small pickup PCB is soldered to the contacts of the 16-pin header, and that board feeds a second PCB carrying the two 8-pin sockets. The card then runs on three cables in total. DallasGrave says each conductor now carries roughly 3 A, and that the wires never crossed 40°C during a 48-hour run at 550 W, even at the joint. More test data is apparently on the way, so for now these are the modder's own numbers.

The 12V-2x6 revision was supposed to fix the melting power connector issues. In early 2025, NVIDIA said the 16-pin melting issues were over, pointing to the updated connector on the RTX 50-series. However, the first melted RTX 5090 Founders Edition was reported shortly after, in that case with a third-party cable. Since then, several RTX 5090 power connectors have reportedly melted, including one with an undervolt and a -100 W power limit. Moreover, last month Hardware Unboxed watched its RTX 5090 power cable reach 175°C with a single wire pulling around 22 A.
Modders have had to jump in with fixes of their own, since off-the-shelf solutions have had a mixed record so far. ASUS introduced the ROG Equalizer cable to spread current more evenly, yet a photo of a burned one later surfaced online. ASRock's TempGuard also reportedly failed to stop a PSU-side meltdown on an RTX PRO 6000 rig. This new mod is clever, though soldering onto a card this expensive is probably best left to experienced hands. It's also a milder approach than what Brazilian channel TecLab did recently, first soldering power wires straight to the PCB and later running an RTX 5090 on three 8-pin connectors. Here, the 16-pin connector stays in use and simply carries less of the load.
Source: Reddit
Add your own comment

86 Comments on Modder Solders Dual 8-Pin Board to RTX 5090's 16-Pin Header, Wires Stay Below 40°C

#76
Vayra86
CrackongSo there are 12 wires carrying all the load...
More than 3x8pin already
ofc it is fine

Oh?

I've been hearing from all the techxperts on this forum that it wasn't just the wiring, but the GPU itself lacking sensing and load balancing. After all the cable had no problems, connector was fine, you just didn't seat it proper, etc.

Its the wires after all if you have sufficient headroom.. my god. Mind blown! Its almost as if we reinvented electronics here. Thanks, tyranny of stupidity. :roll::roll:
Posted on Reply
#77
RejZoR
trsttte~1$ in some smd resistors to measure the current per pin reaching the connector times ~150M cards is 150M$ less the trillion dollar company wouldn't earn 🤷‍♂️

Mass production is about optimising every little cost, unfortunately modern mass production forgot that optimising is not removing features, features that in this case are essential to the reliability of the device. They made a calculus, if RMA remain bellow whatever small % it costs less then spending the 150M$ to make every card more reliable. When boomers say "things used to be built better" this is what they are/should be talking about
Did you miss the part where I said they can double the cost of the said "overbuilt" part and pass it over to the consumer and we wouldn't even notice it? Or did you intentionally ignore it? Literally all this shit costs companies CENTS in additional costs. Passing those DOUBLED to the consumer and would you really notice 20€ difference on a 850€ graphic card? A 1500€ graphic card? Come on, be realistic. You're scraping every € or $ of cost when buying a RTX 5060, you're absolutely not doing it when buying a kitted out RX 9070 XT or RTX 5080/5090. If you or anyone else is doing this then you just failed at basic life economics. I'd rather pay 20€ more for a graphic card or a cable and know it will absolutely not burn up randomly. But I do have RX 9070 XT, the top tier one from XFX money can buy. You can understand I'm not looking to save 20€. Yet they all have same shitty connectors and shitty cables. That's the issue.
Posted on Reply
#78
trsttte
JustBenchingNo, it's called basic common sense. Spending 150m to save 10.000 cards is stupid. That is 15.000 per affected card.
No, it's making a product reliable enough to survive well past it's mandated warranty instead of making it a ticking time bomb calculating that most will fail outside warranty!

Seriously, it ain't about 10000 cards, is there even a source for that number!? It's about consumer confidence in a product, in the case of the 12VHPWR or 12V-6x2 or whatever variation they come up with there's none.
RejZoRDid you miss the part where I said they can double the cost of the said "overbuilt" part and pass it over to the consumer and we wouldn't even notice it? Or did you intentionally ignore it? Literally all this shit costs companies CENTS in additional costs. Passing those DOUBLED to the consumer and would you really notice 20€ difference on a 850€ graphic card? A 1500€ graphic card? Come on, be realistic. You're scraping every € or $ of cost when buying a RTX 5060, you're absolutely not doing it when buying a kitted out RX 9070 XT or RTX 5080/5090. If you or anyone else is doing this then you just failed at basic life economics. I'd rather pay 20€ more for a graphic card or a cable and know it will absolutely not burn up randomly. But I do have RX 9070 XT, the top tier one from XFX money can buy. You can understand I'm not looking to save 20€. Yet they all have same shitty connectors and shitty cables. That's the issue.
That's a simple way to look at it and everyone would be happy to pay that extra dollar but it's not how it works. They made a product and set a price, then they continue to make the product with new revisions having cost optimisations they profit from - i.e. why the 3090 had this and the 4090 didn't. It's not about passing the cost to consumers, it's about passing the savings into the company profit margin.

Realistically they wouldn't need to charge any extra dollar from the start because they have a large enough a profit margin to just do it - this is not asking the company to "be nice" or throw us a bone, just fucking build it properly!
Posted on Reply
#79
JustBenching
trsttteNo, it's making a product reliable enough to survive well past it's mandated warranty instead of making it a ticking time bomb calculating that most will fail outside warranty!

Seriously, it ain't about 10000 cards, is there even a source for that number!? It's about consumer confidence in a product, in the case of the 12VHPWR or 12V-6x2 or whatever variation they come up with there's none.
Most will fail otuside warranty. So we now have 50 million of Ada cards sold in 2022 and 2023 dead. Okay
Posted on Reply
#80
RejZoR
trsttteNo, it's making a product reliable enough to survive well past it's mandated warranty instead of making it a ticking time bomb calculating that most will fail outside warranty!

Seriously, it ain't about 10000 cards, is there even a source for that number!? It's about consumer confidence in a product, in the case of the 12VHPWR or 12V-6x2 or whatever variation they come up with there's none.



That's a simple way to look at it and everyone would be happy to pay that extra dollar but it's not how it works. They made a product and set a price, then they continue to make the product with new revisions having cost optimisations they profit from - i.e. why the 3090 had this and the 4090 didn't. It's not about passing the cost to consumers, it's about passing the savings into the company profit margin.

Realistically they wouldn't need to charge any extra dollar from the start because they have a large enough a profit margin to just do it - this is not asking the company to "be nice" or throw us a bone, just fucking build it properly!
Ah yes, the product at a set price of $699 MSRP being sold for $1200. Because prices are set in stone so hard...
Posted on Reply
#81
Tess
A Computer GuyBut it's not the wire that's the problem right, it's the pins being too small and poor contact situations that are too easy to encounter I thought?
It's both - or seems to be.

This mod might address half the issue.

I dunno why people don't just put thermal probes on the pins and cable at both ends - that would solve everything and it's cheap! Then just poll it every 4s in the background and determine when/if a shutdown condition occurs. If you happen to have a MB with external probes like the Crosshair series etc., I would recommend doing just exactly that!
Posted on Reply
#82
Dragam1337
I am still convinced that the whole thing stems from vanity from nvidia... wanting their sh1tty FE card to only use one connector purely for looks, and then not allowing any AIB partner card to be a better product.

Only exceptions nvidia made to the only one connector allowed rule, were the special edition lighting and matrix cards from msi and asus, which were made in extremely limited numbers.
Posted on Reply
#83
notoperable
lexluthermiesterI have seen thermal imaging of this problem. The wires heat up just as much as the connector. You believe whatever you wish. Physics has something else to say.
you are to gentle, its simpler:
I'll say, you can cheat mum, dad, you can cheat me - but you can't cheat thermodynamics: overhead of energy gotta go somewhere, and it doesn't give a *hit about brand or vendor sentiments. god and entropy figured that part very long time ago.
Posted on Reply
#84
trsttte
RejZoRAh yes, the product at a set price of $699 MSRP being sold for $1200. Because prices are set in stone so hard...
Yet another reason this has nothing to do with passing cost to consumer or not
TesselatorI dunno why people don't just put thermal probes on the pins and cable at both ends
That's what some are doing with wireview and other accessories, it's becoming a product class which is utterly ridiculous
Dragam1337I am still convinced that the whole thing stems from vanity from nvidia... wanting their sh1tty FE card to only use one connector purely for looks
Not really, they were trying to come up with something that worked for both client and server, had higher power and didn't require multiple connectors using PCB space and blocking airflow.

I think the vanity and complete stupidity comes from using micro-fit (or minitek as amphenol calls it) instead of a single mini-fit with more pins. They could have just grown the 8pin we all know to 12 pins and the problem would have been avoided, it's less than 1cm extra width compared to micro-fit/minitek! Could even have used 10pins given how much more capable mini-fit and it'd have been fine! All this was unnecessarily self-caused
Posted on Reply
#85
Tess
trsttteThat's what some are doing with wireview and other accessories, it's becoming a product class which is utterly ridiculous
Agree.
trsttteNot really, they were trying to come up with something that worked for both client and server, had higher power and didn't require multiple connectors using PCB space and blocking airflow.
Yup, if you take a look at heavy metal server components it will become immediately apparent why NVidia designed power delivery the way they did. The problem is, that's not suitable for desktop PCs and on top of that the connector they chose was an extremely poor choice. And I'll speculate, if they thought about airflow at all it was after the fact and only as a marketing point. :P
Posted on Reply
#86
AleXXX666
JustBenchingFractal torrent, a pc case I assume. Topped the airflow charts. I have one, pretty good but not aio friendly, it's for air coolers.
www.fractal-design.com/products/cases/torrent-series/torrent/torrent-black-solid/#specifications
I chose the "boxy" version just because I'm tired of stupid windows inside the cases (not to mess up with OS lmfao:D)
let's see:
Specifications
Compatibility

Front radiator compatibility (YES, I used front-mounting back then and it was pretty ok, not everyone needs to screw AIO at the top only:rolleyes::oops:)
120, 140, 240, 280, 360, 420

Bottom radiator compatibility (ok it's questionable here lol)
120, 140, 240, 280, 360, 420

Rear radiator compatibility (okay, this one is joke-ass, no one need single fan AIO as it's just overpriced POC)
120, 140

So how this case is "not aio friendly" lol:rolleyes::oops:
Posted on Reply
Add your own comment
Nov 20th, 2026 04:57 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts